diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 132 insertions, 68 deletions
diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml b/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml index 26ed040bc717..ffd6ae0eed64 100644 --- a/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml @@ -30,6 +30,20 @@ description: | 3 -- OUT3 4 -- OUT4 + The idt,shutdown and idt,output-enable-active properties control the + SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown + Register, respectively. Their behavior is summarized by the following + table: + + SH SP Output when the SD/OE pin is Low/High + == == ===================================== + 0 0 Active/Inactive + 0 1 Inactive/Active + 1 0 Active/Shutdown + 1 1 Inactive/Shutdown + + The case where SH and SP are both 1 is likely not very interesting. + maintainers: - Luca Ceresoli <luca@lucaceresoli.net> @@ -64,6 +78,26 @@ properties: maximum: 22760 description: Optional load capacitor for XTAL1 and XTAL2 + idt,shutdown: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + If 1, this enables the shutdown functionality: the chip will be + shut down if the SD/OE pin is driven high. If 0, this disables the + shutdown functionality: the chip will never be shut down based on + the value of the SD/OE pin. This property corresponds to the SH + bit of the Primary Source and Shutdown Register. + + idt,output-enable-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + If 1, this enables output when the SD/OE pin is high, and disables + output when the SD/OE pin is low. If 0, this disables output when + the SD/OE pin is high, and enables output when the SD/OE pin is + low. This corresponds to the SP bit of the Primary Source and + Shutdown Register. + patternProperties: "^OUT[1-4]$": type: object @@ -90,6 +124,8 @@ required: - compatible - reg - '#clock-cells' + - idt,shutdown + - idt,output-enable-active allOf: - if: @@ -139,6 +175,10 @@ examples: clocks = <&ref25m>; clock-names = "xin"; + /* Set the SD/OE pin's settings */ + idt,shutdown = <0>; + idt,output-enable-active = <0>; + OUT1 { idt,mode = <VC5_CMOSD>; idt,voltage-microvolt = <1800000>; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt deleted file mode 100644 index 3bc56fae90ac..000000000000 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt +++ /dev/null @@ -1,68 +0,0 @@ -* Rockchip RK3399 Clock and Reset Unit - -The RK3399 clock controller generates and supplies clock to various -controllers within the SoC and also implements a reset controller for SoC -peripherals. - -Required Properties: - -- compatible: PMU for CRU should be "rockchip,rk3399-pmucru" -- compatible: CRU should be "rockchip,rk3399-cru" -- reg: physical base address of the controller and length of memory mapped - region. -- #clock-cells: should be 1. -- #reset-cells: should be 1. - -Optional Properties: - -- rockchip,grf: phandle to the syscon managing the "general register files". - It is used for GRF muxes, if missing any muxes present in the GRF will not - be available. - -Each clock is assigned an identifier and client nodes can use this identifier -to specify the clock which they consume. All available clocks are defined as -preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be -used in device tree sources. Similar macros exist for the reset sources in -these files. - -External clocks: - -There are several clocks that are generated outside the SoC. It is expected -that they are defined using standard clock bindings with following -clock-output-names: - - "xin24m" - crystal input - required, - - "xin32k" - rtc clock - optional, - - "clkin_gmac" - external GMAC clock - optional, - - "clkin_i2s" - external I2S clock - optional, - - "pclkin_cif" - external ISP clock - optional, - - "clk_usbphy0_480m" - output clock of the pll in the usbphy0 - - "clk_usbphy1_480m" - output clock of the pll in the usbphy1 - -Example: Clock controller node: - - pmucru: pmu-clock-controller@ff750000 { - compatible = "rockchip,rk3399-pmucru"; - reg = <0x0 0xff750000 0x0 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - cru: clock-controller@ff760000 { - compatible = "rockchip,rk3399-cru"; - reg = <0x0 0xff760000 0x0 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - -Example: UART controller node that consumes the clock generated by the clock - controller: - - uart0: serial@ff1a0000 { - compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; - reg = <0x0 0xff180000 0x0 0x100>; - clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; - clock-names = "baudclk", "apb_pclk"; - interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <4>; - }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml new file mode 100644 index 000000000000..72b286a1beba --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/rockchip,rk3399-cru.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip RK3399 Clock and Reset Unit + +maintainers: + - Xing Zheng <zhengxing@rock-chips.com> + - Heiko Stuebner <heiko@sntech.de> + +description: | + The RK3399 clock controller generates and supplies clock to various + controllers within the SoC and also implements a reset controller for SoC + peripherals. + Each clock is assigned an identifier and client nodes can use this identifier + to specify the clock which they consume. All available clocks are defined as + preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be + used in device tree sources. Similar macros exist for the reset sources in + these files. + There are several clocks that are generated outside the SoC. It is expected + that they are defined using standard clock bindings with following + clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "clkin_gmac" - external GMAC clock - optional, + - "clkin_i2s" - external I2S clock - optional, + - "pclkin_cif" - external ISP clock - optional, + - "clk_usbphy0_480m" - output clock of the pll in the usbphy0 + - "clk_usbphy1_480m" - output clock of the pll in the usbphy1 + +properties: + compatible: + enum: + - rockchip,rk3399-pmucru + - rockchip,rk3399-cru + + reg: + maxItems: 1 + + "#clock-cells": + const: 1 + + "#reset-cells": + const: 1 + + clocks: + minItems: 1 + + assigned-clocks: + minItems: 1 + maxItems: 64 + + assigned-clock-parents: + minItems: 1 + maxItems: 64 + + assigned-clock-rates: + minItems: 1 + maxItems: 64 + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: > + phandle to the syscon managing the "general register files". It is used + for GRF muxes, if missing any muxes present in the GRF will not be + available. + +required: + - compatible + - reg + - "#clock-cells" + - "#reset-cells" + +additionalProperties: false + +examples: + - | + pmucru: pmu-clock-controller@ff750000 { + compatible = "rockchip,rk3399-pmucru"; + reg = <0xff750000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + - | + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3399-cru"; + reg = <0xff760000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; |