diff options
Diffstat (limited to 'drivers/i2c/busses')
-rw-r--r-- | drivers/i2c/busses/i2c-designware-core.h | 1 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-designware-slave.c | 4 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-img-scb.c | 2 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-imx-lpi2c.c | 4 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-mchp-pci1xxxx.c | 6 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-mv64xxx.c | 11 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-qup.c | 21 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-sprd.c | 8 |
8 files changed, 42 insertions, 15 deletions
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index c5d87aae39c6..bf23bfb51aea 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -40,6 +40,7 @@ #define DW_IC_CON_BUS_CLEAR_CTRL BIT(11) #define DW_IC_DATA_CMD_DAT GENMASK(7, 0) +#define DW_IC_DATA_CMD_FIRST_DATA_BYTE BIT(11) /* * Registers offset diff --git a/drivers/i2c/busses/i2c-designware-slave.c b/drivers/i2c/busses/i2c-designware-slave.c index cec25054bb24..2e079cf20bb5 100644 --- a/drivers/i2c/busses/i2c-designware-slave.c +++ b/drivers/i2c/busses/i2c-designware-slave.c @@ -176,6 +176,10 @@ static irqreturn_t i2c_dw_isr_slave(int this_irq, void *dev_id) do { regmap_read(dev->map, DW_IC_DATA_CMD, &tmp); + if (tmp & DW_IC_DATA_CMD_FIRST_DATA_BYTE) + i2c_slave_event(dev->slave, + I2C_SLAVE_WRITE_REQUESTED, + &val); val = tmp; i2c_slave_event(dev->slave, I2C_SLAVE_WRITE_RECEIVED, &val); diff --git a/drivers/i2c/busses/i2c-img-scb.c b/drivers/i2c/busses/i2c-img-scb.c index 8e987945ed45..39c479f96eb5 100644 --- a/drivers/i2c/busses/i2c-img-scb.c +++ b/drivers/i2c/busses/i2c-img-scb.c @@ -257,7 +257,7 @@ #define IMG_I2C_TIMEOUT (msecs_to_jiffies(1000)) /* - * Worst incs are 1 (innacurate) and 16*256 (irregular). + * Worst incs are 1 (inaccurate) and 16*256 (irregular). * So a sensible inc is the logarithmic mean: 64 (2^6), which is * in the middle of the valid range (0-127). */ diff --git a/drivers/i2c/busses/i2c-imx-lpi2c.c b/drivers/i2c/busses/i2c-imx-lpi2c.c index 1af0a637d7f1..4d24ceb57ee7 100644 --- a/drivers/i2c/busses/i2c-imx-lpi2c.c +++ b/drivers/i2c/busses/i2c-imx-lpi2c.c @@ -201,8 +201,8 @@ static void lpi2c_imx_stop(struct lpi2c_imx_struct *lpi2c_imx) /* CLKLO = I2C_CLK_RATIO * CLKHI, SETHOLD = CLKHI, DATAVD = CLKHI/2 */ static int lpi2c_imx_config(struct lpi2c_imx_struct *lpi2c_imx) { - u8 prescale, filt, sethold, clkhi, clklo, datavd; - unsigned int clk_rate, clk_cycle; + u8 prescale, filt, sethold, datavd; + unsigned int clk_rate, clk_cycle, clkhi, clklo; enum lpi2c_imx_pincfg pincfg; unsigned int temp; diff --git a/drivers/i2c/busses/i2c-mchp-pci1xxxx.c b/drivers/i2c/busses/i2c-mchp-pci1xxxx.c index b21ffd6df927..5ef136c3ecb1 100644 --- a/drivers/i2c/busses/i2c-mchp-pci1xxxx.c +++ b/drivers/i2c/busses/i2c-mchp-pci1xxxx.c @@ -1118,8 +1118,10 @@ static int pci1xxxx_i2c_resume(struct device *dev) static DEFINE_SIMPLE_DEV_PM_OPS(pci1xxxx_i2c_pm_ops, pci1xxxx_i2c_suspend, pci1xxxx_i2c_resume); -static void pci1xxxx_i2c_shutdown(struct pci1xxxx_i2c *i2c) +static void pci1xxxx_i2c_shutdown(void *data) { + struct pci1xxxx_i2c *i2c = data; + pci1xxxx_i2c_config_padctrl(i2c, false); pci1xxxx_i2c_configure_core_reg(i2c, false); } @@ -1156,7 +1158,7 @@ static int pci1xxxx_i2c_probe_pci(struct pci_dev *pdev, init_completion(&i2c->i2c_xfer_done); pci1xxxx_i2c_init(i2c); - ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c); + ret = devm_add_action(dev, pci1xxxx_i2c_shutdown, i2c); if (ret) return ret; diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c index 047dfef7a657..878c076ebdc6 100644 --- a/drivers/i2c/busses/i2c-mv64xxx.c +++ b/drivers/i2c/busses/i2c-mv64xxx.c @@ -520,6 +520,17 @@ mv64xxx_i2c_intr(int irq, void *dev_id) while (readl(drv_data->reg_base + drv_data->reg_offsets.control) & MV64XXX_I2C_REG_CONTROL_IFLG) { + /* + * It seems that sometime the controller updates the status + * register only after it asserts IFLG in control register. + * This may result in weird bugs when in atomic mode. A delay + * of 100 ns before reading the status register solves this + * issue. This bug does not seem to appear when using + * interrupts. + */ + if (drv_data->atomic) + ndelay(100); + status = readl(drv_data->reg_base + drv_data->reg_offsets.status); mv64xxx_i2c_fsm(drv_data, status); mv64xxx_i2c_do_action(drv_data); diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c index 2e153f2f71b6..78682388e02e 100644 --- a/drivers/i2c/busses/i2c-qup.c +++ b/drivers/i2c/busses/i2c-qup.c @@ -1752,16 +1752,21 @@ nodma: if (!clk_freq || clk_freq > I2C_MAX_FAST_MODE_PLUS_FREQ) { dev_err(qup->dev, "clock frequency not supported %d\n", clk_freq); - return -EINVAL; + ret = -EINVAL; + goto fail_dma; } qup->base = devm_platform_ioremap_resource(pdev, 0); - if (IS_ERR(qup->base)) - return PTR_ERR(qup->base); + if (IS_ERR(qup->base)) { + ret = PTR_ERR(qup->base); + goto fail_dma; + } qup->irq = platform_get_irq(pdev, 0); - if (qup->irq < 0) - return qup->irq; + if (qup->irq < 0) { + ret = qup->irq; + goto fail_dma; + } if (has_acpi_companion(qup->dev)) { ret = device_property_read_u32(qup->dev, @@ -1775,13 +1780,15 @@ nodma: qup->clk = devm_clk_get(qup->dev, "core"); if (IS_ERR(qup->clk)) { dev_err(qup->dev, "Could not get core clock\n"); - return PTR_ERR(qup->clk); + ret = PTR_ERR(qup->clk); + goto fail_dma; } qup->pclk = devm_clk_get(qup->dev, "iface"); if (IS_ERR(qup->pclk)) { dev_err(qup->dev, "Could not get iface clock\n"); - return PTR_ERR(qup->pclk); + ret = PTR_ERR(qup->pclk); + goto fail_dma; } qup_i2c_enable_clocks(qup); src_clk_freq = clk_get_rate(qup->clk); diff --git a/drivers/i2c/busses/i2c-sprd.c b/drivers/i2c/busses/i2c-sprd.c index 4fe15cd78907..ffc54fbf814d 100644 --- a/drivers/i2c/busses/i2c-sprd.c +++ b/drivers/i2c/busses/i2c-sprd.c @@ -576,12 +576,14 @@ static int sprd_i2c_remove(struct platform_device *pdev) struct sprd_i2c *i2c_dev = platform_get_drvdata(pdev); int ret; - ret = pm_runtime_resume_and_get(i2c_dev->dev); + ret = pm_runtime_get_sync(i2c_dev->dev); if (ret < 0) - return ret; + dev_err(&pdev->dev, "Failed to resume device (%pe)\n", ERR_PTR(ret)); i2c_del_adapter(&i2c_dev->adap); - clk_disable_unprepare(i2c_dev->clk); + + if (ret >= 0) + clk_disable_unprepare(i2c_dev->clk); pm_runtime_put_noidle(i2c_dev->dev); pm_runtime_disable(i2c_dev->dev); |