| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Large effort by Eric to lower rtnl_lock pressure and remove locks:
- Make commonly used parts of rtnetlink (address, route dumps
etc) lockless, protected by RCU instead of rtnl_lock.
- Add a netns exit callback which already holds rtnl_lock,
allowing netns exit to take rtnl_lock once in the core instead
of once for each driver / callback.
- Remove locks / serialization in the socket diag interface.
- Remove 6 calls to synchronize_rcu() while holding rtnl_lock.
- Remove the dev_base_lock, depend on RCU where necessary.
- Support busy polling on a per-epoll context basis. Poll length and
budget parameters can be set independently of system defaults.
- Introduce struct net_hotdata, to make sure read-mostly global
config variables fit in as few cache lines as possible.
- Add optional per-nexthop statistics to ease monitoring / debug of
ECMP imbalance problems.
- Support TCP_NOTSENT_LOWAT in MPTCP.
- Ensure that IPv6 temporary addresses' preferred lifetimes are long
enough, compared to other configured lifetimes, and at least 2 sec.
- Support forwarding of ICMP Error messages in IPSec, per RFC 4301.
- Add support for the independent control state machine for bonding
per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
control state machine.
- Add "network ID" to MCTP socket APIs to support hosts with multiple
disjoint MCTP networks.
- Re-use the mono_delivery_time skbuff bit for packets which user
space wants to be sent at a specified time. Maintain the timing
information while traversing veth links, bridge etc.
- Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.
- Simplify many places iterating over netdevs by using an xarray
instead of a hash table walk (hash table remains in place, for use
on fastpaths).
- Speed up scanning for expired routes by keeping a dedicated list.
- Speed up "generic" XDP by trying harder to avoid large allocations.
- Support attaching arbitrary metadata to netconsole messages.
Things we sprinkled into general kernel code:
- Enforce VM_IOREMAP flag and range in ioremap_page_range and
introduce VM_SPARSE kind and vm_area_[un]map_pages (used by
bpf_arena).
- Rework selftest harness to enable the use of the full range of ksft
exit code (pass, fail, skip, xfail, xpass).
Netfilter:
- Allow userspace to define a table that is exclusively owned by a
daemon (via netlink socket aliveness) without auto-removing this
table when the userspace program exits. Such table gets marked as
orphaned and a restarting management daemon can re-attach/regain
ownership.
- Speed up element insertions to nftables' concatenated-ranges set
type. Compact a few related data structures.
BPF:
- Add BPF token support for delegating a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application.
- Introduce bpf_arena which is sparse shared memory region between
BPF program and user space where structures inside the arena can
have pointers to other areas of the arena, and pointers work
seamlessly for both user-space programs and BPF programs.
- Introduce may_goto instruction that is a contract between the
verifier and the program. The verifier allows the program to loop
assuming it's behaving well, but reserves the right to terminate
it.
- Extend the BPF verifier to enable static subprog calls in spin lock
critical sections.
- Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops
type.
- Add support for retrieval of cookies for perf/kprobe multi links.
- Support arbitrary TCP SYN cookie generation / validation in the TC
layer with BPF to allow creating SYN flood handling in BPF
firewalls.
- Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF
objects.
Wireless:
- Add SPP (signaling and payload protected) AMSDU support.
- Support wider bandwidth OFDMA, as required for EHT operation.
Driver API:
- Major overhaul of the Energy Efficient Ethernet internals to
support new link modes (2.5GE, 5GE), share more code between
drivers (especially those using phylib), and encourage more
uniform behavior. Convert and clean up drivers.
- Define an API for querying per netdev queue statistics from
drivers.
- IPSec: account in global stats for fully offloaded sessions.
- Create a concept of Ethernet PHY Packages at the Device Tree level,
to allow parameterizing the existing PHY package code.
- Enable Rx hashing (RSS) on GTP protocol fields.
Misc:
- Improvements and refactoring all over networking selftests.
- Create uniform module aliases for TC classifiers, actions, and
packet schedulers to simplify creating modprobe policies.
- Address all missing MODULE_DESCRIPTION() warnings in networking.
- Extend the Netlink descriptions in YAML to cover message
encapsulation or "Netlink polymorphism", where interpretation of
nested attributes depends on link type, classifier type or some
other "class type".
Drivers:
- Ethernet high-speed NICs:
- Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
- Intel (100G, ice, idpf):
- support E825-C devices
- nVidia/Mellanox:
- support devices with one port and multiple PCIe links
- Broadcom (bnxt):
- support n-tuple filters
- support configuring the RSS key
- Wangxun (ngbe/txgbe):
- implement irq_domain for TXGBE's sub-interrupts
- Pensando/AMD:
- support XDP
- optimize queue submission and wakeup handling (+17% bps)
- optimize struct layout, saving 28% of memory on queues
- Ethernet NICs embedded and virtual:
- Google cloud vNIC:
- refactor driver to perform memory allocations for new queue
config before stopping and freeing the old queue memory
- Synopsys (stmmac):
- obey queueMaxSDU and implement counters required by 802.1Qbv
- Renesas (ravb):
- support packet checksum offload
- suspend to RAM and runtime PM support
- Ethernet switches:
- nVidia/Mellanox:
- support for nexthop group statistics
- Microchip:
- ksz8: implement PHY loopback
- add support for KSZ8567, a 7-port 10/100Mbps switch
- PTP:
- New driver for RENESAS FemtoClock3 Wireless clock generator.
- Support OCP PTP cards designed and built by Adva.
- CAN:
- Support recvmsg() flags for own, local and remote traffic on CAN
BCM sockets.
- Support for esd GmbH PCIe/402 CAN device family.
- m_can:
- Rx/Tx submission coalescing
- wake on frame Rx
- WiFi:
- Intel (iwlwifi):
- enable signaling and payload protected A-MSDUs
- support wider-bandwidth OFDMA
- support for new devices
- bump FW API to 89 for AX devices; 90 for BZ/SC devices
- MediaTek (mt76):
- mt7915: newer ADIE version support
- mt7925: radio temperature sensor support
- Qualcomm (ath11k):
- support 6 GHz station power modes: Low Power Indoor (LPI),
Standard Power) SP and Very Low Power (VLP)
- QCA6390 & WCN6855: support 2 concurrent station interfaces
- QCA2066 support
- Qualcomm (ath12k):
- refactoring in preparation for Multi-Link Operation (MLO)
support
- 1024 Block Ack window size support
- firmware-2.bin support
- support having multiple identical PCI devices (firmware needs
to have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
- QCN9274: support split-PHY devices
- WCN7850: enable Power Save Mode in station mode
- WCN7850: P2P support
- RealTek:
- rtw88: support for more rtw8811cu and rtw8821cu devices
- rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
- rtlwifi: speed up USB firmware initialization
- rtwl8xxxu:
- RTL8188F: concurrent interface support
- Channel Switch Announcement (CSA) support in AP mode
- Broadcom (brcmfmac):
- per-vendor feature support
- per-vendor SAE password setup
- DMI nvram filename quirk for ACEPC W5 Pro"
* tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2255 commits)
nexthop: Fix splat with CONFIG_DEBUG_PREEMPT=y
nexthop: Fix out-of-bounds access during attribute validation
nexthop: Only parse NHA_OP_FLAGS for dump messages that require it
nexthop: Only parse NHA_OP_FLAGS for get messages that require it
bpf: move sleepable flag from bpf_prog_aux to bpf_prog
bpf: hardcode BPF_PROG_PACK_SIZE to 2MB * num_possible_nodes()
selftests/bpf: Add kprobe multi triggering benchmarks
ptp: Move from simple ida to xarray
vxlan: Remove generic .ndo_get_stats64
vxlan: Do not alloc tstats manually
devlink: Add comments to use netlink gen tool
nfp: flower: handle acti_netdevs allocation failure
net/packet: Add getsockopt support for PACKET_COPY_THRESH
net/netlink: Add getsockopt support for NETLINK_LISTEN_ALL_NSID
selftests/bpf: Add bpf_arena_htab test.
selftests/bpf: Add bpf_arena_list test.
selftests/bpf: Add unit tests for bpf_arena_alloc/free_pages
bpf: Add helper macro bpf_addr_space_cast()
libbpf: Recognize __arena global variables.
bpftool: Recognize arena map type
...
|
|
Pull documentation updates from Jonathan Corbet:
"A moderatly busy cycle for development this time around.
- Some cleanup of the main index page for easier navigation
- Rework some of the other top-level pages for better readability
and, with luck, fewer merge conflicts in the future.
- Submit-checklist improvements, hopefully the first of many.
- New Italian translations
- A fair number of kernel-doc fixes and improvements. We have also
dropped the recommendation to use an old version of Sphinx.
- A new document from Thorsten on bisection
... and lots of fixes and updates"
* tag 'docs-6.9' of git://git.lwn.net/linux: (54 commits)
docs: verify/bisect: fixes, finetuning, and support for Arch
docs: Makefile: Add dependency to $(YNL_INDEX) for targets other than htmldocs
docs: Move ja_JP/howto.rst to ja_JP/process/howto.rst
docs: submit-checklist: use subheadings
docs: submit-checklist: structure by category
docs: new text on bisecting which also covers bug validation
docs: drop the version constraints for sphinx and dependencies
docs: kerneldoc-preamble.sty: Remove code for Sphinx <2.4
docs: Restore "smart quotes" for quotes
docs/zh_CN: accurate translation of "function"
docs: Include simplified link titles in main index
docs: Correct formatting of title in admin-guide/index.rst
docs: kernel_feat.py: fix build error for missing files
MAINTAINERS: Set the field name for subsystem profile section
kasan: Add documentation for CONFIG_KASAN_EXTRA_INFO
Fixed case issue with 'fault-injection' in documentation
kernel-doc: handle #if in enums as well
Documentation: update mailing list addresses
doc: kerneldoc.py: fix indentation
scripts/kernel-doc: simplify signature printing
...
|
|
Add a space (' ') prefix to every userdata line to match docs for
dev-kmsg. To account for this extra character in each userdata entry,
reduce userdata entry names (directory name) from 54 characters to 53.
According to the dev-kmsg docs, a space is used for subsequent lines to
mark them as continuation lines.
> A line starting with ' ', is a continuation line, adding
> key/value pairs to the log message, which provide the machine
> readable context of the message, for reliable processing in
> userspace.
Testing for this patch::
cd /sys/kernel/config/netconsole && mkdir cmdline0
cd cmdline0
mkdir userdata/test && echo "hello" > userdata/test/value
mkdir userdata/test2 && echo "hello2" > userdata/test2/value
echo "message" > /dev/kmsg
Outputs::
6.8.0-rc5-virtme,12,493,231373579,-;message
test=hello
test2=hello2
And I confirmed all testing works as expected from the original patchset
Fixes: df03f830d099 ("net: netconsole: cache userdata formatted string in netconsole_target")
Signed-off-by: Matthew Wood <thepacketgeek@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240308002525.248672-1-thepacketgeek@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ethtool: ice: Support for RSS settings to GTP
Takeru Hayasaka enables RSS functionality for GTP packets on ice driver
with ethtool.
A user can include TEID and make RSS work for GTP-U over IPv4 by doing the
following:`ethtool -N ens3 rx-flow-hash gtpu4 sde`
In addition to gtpu(4|6), we now support gtpc(4|6),gtpc(4|6)t,gtpu(4|6)e,
gtpu(4|6)u, and gtpu(4|6)d.
gtpc(4|6): Used for GTP-C in IPv4 and IPv6, where the GTP header format does
not include a TEID.
gtpc(4|6)t: Used for GTP-C in IPv4 and IPv6, with a GTP header format that
includes a TEID.
gtpu(4|6): Used for GTP-U in both IPv4 and IPv6 scenarios.
gtpu(4|6)e: Used for GTP-U with extended headers in both IPv4 and IPv6.
gtpu(4|6)u: Used when the PSC (PDU session container) in the GTP-U extended
header includes Uplink, applicable to both IPv4 and IPv6.
gtpu(4|6)d: Used when the PSC in the GTP-U extended header includes Downlink,
for both IPv4 and IPv6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Support Multi-PF netdev (Socket Direct)
This series adds support for combining multiple devices (PFs) of the
same port under one netdev instance. Passing traffic through different
devices belonging to different NUMA sockets saves cross-numa traffic and
allows apps running on the same netdev from different numas to still
feel a sense of proximity to the device and achieve improved
performance.
We achieve this by grouping PFs together, and creating the netdev only
once all group members are probed. Symmetrically, we destroy the netdev
once any of the PFs is removed.
The channels are distributed between all devices, a proper configuration
would utilize the correct close numa when working on a certain app/cpu.
We pick one device to be a primary (leader), and it fills a special
role. The other devices (secondaries) are disconnected from the network
in the chip level (set to silent mode). All RX/TX traffic is steered
through the primary to/from the secondaries.
Currently, we limit the support to PFs only, and up to two devices
(sockets).
* tag 'mlx5-socket-direct-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
Documentation: networking: Add description for multi-pf netdev
net/mlx5: Enable SD feature
net/mlx5e: Block TLS device offload on combined SD netdev
net/mlx5e: Support per-mdev queue counter
net/mlx5e: Support cross-vhca RSS
net/mlx5e: Let channels be SD-aware
net/mlx5e: Create EN core HW resources for all secondary devices
net/mlx5e: Create single netdev per SD group
net/mlx5: SD, Add debugfs
net/mlx5: SD, Add informative prints in kernel log
net/mlx5: SD, Implement steering for primary and secondaries
net/mlx5: SD, Implement devcom communication and primary election
net/mlx5: SD, Implement basic query and instantiation
net/mlx5: SD, Introduce SD lib
net/mlx5: Add MPIR bit in mcam_access_reg
====================
Link: https://lore.kernel.org/r/20240307084229.500776-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ethtool-nl family does a good job exposing various protocol
related and IEEE/IETF statistics which used to get dumped under
ethtool -S, with creative names. Queue stats don't have a netlink
API, yet, and remain a lion's share of ethtool -S output for new
drivers. Not only is that bad because the names differ driver to
driver but it's also bug-prone. Intuitively drivers try to report
only the stats for active queues, but querying ethtool stats
involves multiple system calls, and the number of stats is
read separately from the stats themselves. Worse still when user
space asks for values of the stats, it doesn't inform the kernel
how big the buffer is. If number of stats increases in the meantime
kernel will overflow user buffer.
Add a netlink API for dumping queue stats. Queue information is
exposed via the netdev-genl family, so add the stats there.
Support per-queue and sum-for-device dumps. Latter will be useful
when subsequent patches add more interesting common stats than
just bytes and packets.
The API does not currently distinguish between HW and SW stats.
The expectation is that the source of the stats will either not
matter much (good packets) or be obvious (skb alloc errors).
Acked-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240306195509.1502746-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that phylink has a comprehensive PCS support, update the porting
guide to explain the process of supporting the PCS configuration. This
also removed outdated references to phylink_config fields that no longer
exists.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add documentation for the multi-pf netdev feature.
Describe the mlx5 implementation and design decisions.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
|
|
Following the addition of new GTP RSS hash options to ethtool.h, this patch
implements the corresponding RSS settings for GTP packets in the Intel ice
driver. It enables users to configure RSS for GTP-U and GTP-C traffic over IPv4
and IPv6, utilizing the newly defined hash options.
The implementation covers the handling of gtpu(4|6), gtpc(4|6), gtpc(4|6)t,
gtpu(4|6)e, gtpu(4|6)u, and gtpu(4|6)d traffic, providing enhanced load
distribution for GTP traffic across multiple processing units.
Signed-off-by: Takeru Hayasaka <hayatake396@gmail.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2024-02-29
We've added 119 non-merge commits during the last 32 day(s) which contain
a total of 150 files changed, 3589 insertions(+), 995 deletions(-).
The main changes are:
1) Extend the BPF verifier to enable static subprog calls in spin lock
critical sections, from Kumar Kartikeya Dwivedi.
2) Fix confusing and incorrect inference of PTR_TO_CTX argument type
in BPF global subprogs, from Andrii Nakryiko.
3) Larger batch of riscv BPF JIT improvements and enabling inlining
of the bpf_kptr_xchg() for RV64, from Pu Lehui.
4) Allow skeleton users to change the values of the fields in struct_ops
maps at runtime, from Kui-Feng Lee.
5) Extend the verifier's capabilities of tracking scalars when they
are spilled to stack, especially when the spill or fill is narrowing,
from Maxim Mikityanskiy & Eduard Zingerman.
6) Various BPF selftest improvements to fix errors under gcc BPF backend,
from Jose E. Marchesi.
7) Avoid module loading failure when the module trying to register
a struct_ops has its BTF section stripped, from Geliang Tang.
8) Annotate all kfuncs in .BTF_ids section which eventually allows
for automatic kfunc prototype generation from bpftool, from Daniel Xu.
9) Several updates to the instruction-set.rst IETF standardization
document, from Dave Thaler.
10) Shrink the size of struct bpf_map resp. bpf_array,
from Alexei Starovoitov.
11) Initial small subset of BPF verifier prepwork for sleepable bpf_timer,
from Benjamin Tissoires.
12) Fix bpftool to be more portable to musl libc by using POSIX's
basename(), from Arnaldo Carvalho de Melo.
13) Add libbpf support to gcc in CORE macro definitions,
from Cupertino Miranda.
14) Remove a duplicate type check in perf_event_bpf_event,
from Florian Lehner.
15) Fix bpf_spin_{un,}lock BPF helpers to actually annotate them
with notrace correctly, from Yonghong Song.
16) Replace the deprecated bpf_lpm_trie_key 0-length array with flexible
array to fix build warnings, from Kees Cook.
17) Fix resolve_btfids cross-compilation to non host-native endianness,
from Viktor Malik.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (119 commits)
selftests/bpf: Test if shadow types work correctly.
bpftool: Add an example for struct_ops map and shadow type.
bpftool: Generated shadow variables for struct_ops maps.
libbpf: Convert st_ops->data to shadow type.
libbpf: Set btf_value_type_id of struct bpf_map for struct_ops.
bpf: Replace bpf_lpm_trie_key 0-length array with flexible array
bpf, arm64: use bpf_prog_pack for memory management
arm64: patching: implement text_poke API
bpf, arm64: support exceptions
arm64: stacktrace: Implement arch_bpf_stack_walk() for the BPF JIT
bpf: add is_async_callback_calling_insn() helper
bpf: introduce in_sleepable() helper
bpf: allow more maps in sleepable bpf programs
selftests/bpf: Test case for lacking CFI stub functions.
bpf: Check cfi_stubs before registering a struct_ops type.
bpf: Clarify batch lookup/lookup_and_delete semantics
bpf, docs: specify which BPF_ABS and BPF_IND fields were zero
bpf, docs: Fix typos in instruction-set.rst
selftests/bpf: update tcp_custom_syncookie to use scalar packet offset
bpf: Shrink size of struct bpf_map/bpf_array.
...
====================
Link: https://lore.kernel.org/r/20240301001625.8800-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/mptcp/protocol.c
adf1bb78dab5 ("mptcp: fix snd_wnd initialization for passive socket")
9426ce476a70 ("mptcp: annotate lockless access for RX path fields")
https://lore.kernel.org/all/20240228103048.19255709@canb.auug.org.au/
Adjacent changes:
drivers/dpll/dpll_core.c
0d60d8df6f49 ("dpll: rely on rcu for netdev_dpll_pin()")
e7f8df0e81bf ("dpll: move xa_erase() call in to match dpll_pin_alloc() error path order")
drivers/net/veth.c
1ce7d306ea63 ("veth: try harder when allocating queue memory")
0bef512012b1 ("net: add netdev_lockdep_set_classes() to virtual drivers")
drivers/net/wireless/intel/iwlwifi/mvm/d3.c
8c9bef26e98b ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
78f65fbf421a ("wifi: iwlwifi: mvm: ensure offloading TID queue exists")
net/wireless/nl80211.c
f78c1375339a ("wifi: nl80211: reject iftype change with mesh ID change")
414532d8aa89 ("wifi: cfg80211: use IEEE80211_MAX_MESH_ID_LEN appropriately")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fast path usage breakdown describes the detail for 'inet_sock', fix
the markup title.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing documentation was not telling that one has to create a PPP
channel and a PPP interface to get PPPoL2TP data offloading working.
Also, tunnel switching was not mentioned, so that people were thinking
it was not supported, while it actually is.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Tom Parkin <tparkin@katalix.com>
Link: https://lore.kernel.org/r/20240217211425.qj576u3jmaa6yidf@begin
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mailman2 server running on lists.linuxfoundation.org will be shut
down in very imminent future. Update all instances of obsolete list
addresses throughout the tree with their new destinations.
Signed-off-by: Konstantin Ryabitsev <konstantin@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240214-lf-org-list-migration-v1-1-ef1eab4b1543@linuxfoundation.org
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/dev.c
9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()")
723de3ebef03 ("net: free altname using an RCU callback")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
drivers/net/ethernet/renesas/ravb_main.c
ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path"
)
c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
net/mptcp/protocol.c
bdd70eb68913 ("mptcp: drop the push_pending field")
28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the preferred lifetime was less than the minimum required lifetime,
ipv6_create_tempaddr would error out without creating any new address.
On my machine and network, this error happened immediately with the
preferred lifetime set to 5 seconds or less, after a few minutes with
the preferred lifetime set to 6 seconds, and not at all with the
preferred lifetime set to 7 seconds. During my investigation, I found a
Stack Exchange post from another person who seems to have had the same
problem: They stopped getting new addresses if they lowered the
preferred lifetime below 3 seconds, and they didn't really know why.
The preferred lifetime is a preference, not a hard requirement. The
kernel does not strictly forbid new connections on a deprecated address,
nor does it guarantee that the address will be disposed of the instant
its total valid lifetime expires. So rather than disable IPv6 privacy
extensions altogether if the minimum required lifetime swells above the
preferred lifetime, it is more in keeping with the user's intent to
increase the temporary address's lifetime to the minimum necessary for
the current network conditions.
With these fixes, setting the preferred lifetime to 5 or 6 seconds "just
works" because the extra fraction of a second is practically
unnoticeable. It's even possible to reduce the time before deprecation
to 1 or 2 seconds by setting /proc/sys/net/ipv6/conf/*/regen_min_advance
and /proc/sys/net/ipv6/conf/*/dad_transmits to 0. I realize that that is
a pretty niche use case, but I know at least one person who would gladly
sacrifice performance and convenience to be sure that they are getting
the maximum possible level of privacy.
Link: https://serverfault.com/a/1031168/310447
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In RFC 8981, REGEN_ADVANCE cannot be less than 2 seconds, and the RFC
does not permit the creation of temporary addresses with lifetimes
shorter than that:
> When processing a Router Advertisement with a
> Prefix Information option carrying a prefix for the purposes of
> address autoconfiguration (i.e., the A bit is set), the host MUST
> perform the following steps:
> 5. A temporary address is created only if this calculated preferred
> lifetime is greater than REGEN_ADVANCE time units.
However, some users want to change their IPv6 address as frequently as
possible regardless of the RFC's arbitrary minimum lifetime. For the
benefit of those users, add a regen_min_advance sysctl parameter that
can be set to below or above 2 seconds.
Link: https://datatracker.ietf.org/doc/html/rfc8981
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RFC 8981 defines REGEN_ADVANCE as follows:
REGEN_ADVANCE = 2 + (TEMP_IDGEN_RETRIES * DupAddrDetectTransmits * RetransTimer / 1000)
Thus, allowing it to be less than 2 seconds is technically a protocol
violation.
Link: https://datatracker.ietf.org/doc/html/rfc8981#name-defined-protocol-parameters
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Change comments incorrectly mentioning dev_base_lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-6.9-20240213
this is a pull request of 23 patches for net-next/master.
The first patch is by Nicolas Maier and targets the CAN Broadcast
Manager (bcm), it adds message flags to distinguish between own local
and remote traffic.
Oliver Hartkopp contributes a patch for the CAN ISOTP protocol that
adds dynamic flow control parameters.
Stefan Mätje's patch series add support for the esd PCIe/402 CAN
interface family.
Markus Schneider-Pargmann contributes 14 patches for the m_can to
optimize for the SPI attached tcan4x5x controller.
A patch by Vincent Mailhol replaces Wolfgang Grandegger by Vincent
Mailhol as the CAN drivers Co-Maintainer.
Jimmy Assarsson's patch add support for the Kvaser M.2 PCIe 4xCAN
adapter.
A patch by Daniil Dulov removed a redundant NULL check in the softing
driver.
Oliver Hartkopp contributes a patch to add CANXL virtual CAN network
identifier support.
A patch by myself removes Naga Sureshkumar Relli as the maintainer of
the xilinx_can driver, as their email bounces.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CAN RAW sockets allow userspace to tell if a received CAN frame comes
from the same socket, another socket on the same host, or another host.
See commit 1e55659ce6dd ("can-raw: add msg_flags to distinguish local
traffic"). However, this feature is missing in CAN BCM sockets.
Add the same feature to CAN BCM sockets. When reading a received frame
(opcode RX_CHANGED) using recvmsg, two flags in msg->msg_flags may be
set following the previous convention (from CAN RAW), to distinguish
between 'own', 'local' and 'remote' CAN traffic.
Update the documentation to reflect this change.
Signed-off-by: Nicolas Maier <nicolas.maier.dev@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20240120081018.2319-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
dev->lstats is notably used from loopback ndo_start_xmit()
and other virtual drivers.
Per cpu stats updates are dirtying per-cpu data,
but the pointer itself is read-only.
Fixes: 43a71cd66b9c ("net-device: reorganize net_device fast path variables")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tp->tcp_usec_ts is a read mostly field, used in rx and tx fast paths.
Fixes: d5fed5addb2b ("tcp: reorganize tcp_sock fast path variables")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Wei Wang <weiwan@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tp->scaling_ratio is a read mostly field, used in rx and tx fast paths.
Fixes: d5fed5addb2b ("tcp: reorganize tcp_sock fast path variables")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Wei Wang <weiwan@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver framework and device setup and initialization for Octeon
PCI Endpoint NIC VF.
Add implementation to load module, initialize, register network device,
cleanup and unload module.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On early detection of wwan device in fastboot mode, driver sets
up CLDMA0 HW tx/rx queues for raw data transfer and then create
fastboot port to userspace.
Application can use this port to flash firmware and collect
core dump by fastboot protocol commands.
E.g., flash firmware through fastboot port:
- "download:%08x": write data to memory with the download size.
- "flash:%s": write the previously downloaded image to the named partition.
- "reboot": reboot the device.
Link: https://android.googlesource.com/platform/system/core/+/refs/heads/main/fastboot/README.md
Signed-off-by: Jinjian Song <jinjian.song@fibocom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for userspace to get/set the device mode, device's state
machine changes between (unknown/ready/reset/fastboot).
Get the device state mode:
- 'cat /sys/bus/pci/devices/${bdf}/t7xx_mode'
Set the device state mode:
- reset(cold reset): 'echo reset > /sys/bus/pci/devices/${bdf}/t7xx_mode'
- fastboot: 'echo fastboot_switching > /sys/bus/pci/devices/${bdf}/t7xx_mode'
Reload driver to get the new device state after setting operation.
Signed-off-by: Jinjian Song <jinjian.song@fibocom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new User Data section to the netconsole docs to describe the
appending of user data capability (for netconsole dynamic configuration)
with usage and netconsole output examples.
Co-developed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Matthew Wood <thepacketgeek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Command example string is not read as command.
Fix command annotation.
Fixes: a8ce7b26a51e ("devlink: Expose port function commands to control migratable")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206161717.466653-1-parav@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2024-02-01
1) IPSec global stats for xfrm and mlx5
2) XSK memory improvements for non-linear SKBs
3) Software steering debug dump to use seq_file ops
4) Various code clean-ups
* tag 'mlx5-updates-2024-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: XDP, Exclude headroom and tailroom from memory calculations
net/mlx5e: XSK, Exclude tailroom from non-linear SKBs memory calculations
net/mlx5: DR, Change SWS usage to debug fs seq_file interface
net/mlx5: Change missing SyncE capability print to debug
net/mlx5: Remove initial segmentation duplicate definitions
net/mlx5: Return specific error code for timeout on wait_fw_init
net/mlx5: SF, Stop waiting for FW as teardown was called
net/mlx5: remove fw reporter dump option for non PF
net/mlx5: remove fw_fatal reporter dump option for non PF
net/mlx5: Rename mlx5_sf_dev_remove
Documentation: Fix counter name of mlx5 vnic reporter
net/mlx5e: Delete obsolete IPsec code
net/mlx5e: Connect mlx5 IPsec statistics with XFRM core
xfrm: get global statistics from the offloaded device
xfrm: generalize xdo_dev_state_update_curlft to allow statistics update
====================
Link: https://lore.kernel.org/r/20240206005527.1353368-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the independent control state machine per IEEE
802.1AX-2008 5.4.15 in addition to the existing implementation of the
coupled control state machine.
Introduces two new states, AD_MUX_COLLECTING and AD_MUX_DISTRIBUTING in
the LACP MUX state machine for separated handling of an initial
Collecting state before the Collecting and Distributing state. This
enables a port to be in a state where it can receive incoming packets
while not still distributing. This is useful for reducing packet loss when
a port begins distributing before its partner is able to collect.
Added new functions such as bond_set_slave_tx_disabled_flags and
bond_set_slave_rx_enabled_flags to precisely manage the port's collecting
and distributing states. Previously, there was no dedicated method to
disable TX while keeping RX enabled, which this patch addresses.
Note that the regular flow process in the kernel's bonding driver remains
unaffected by this patch. The extension requires explicit opt-in by the
user (in order to ensure no disruptions for existing setups) via netlink
support using the new bonding parameter coupled_control. The default value
for coupled_control is set to 1 so as to preserve existing behaviour.
Signed-off-by: Aahil Awatramani <aahila@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240202175858.1573852-1-aahila@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Document the ability to redirect to any socket bound to the same umem.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/r/20240205123553.22180-3-magnus.karlsson@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Fix counter name in documentation of mlx5 vnic health reporter diagnose
output: total_error_queues.
While here fix alignment in the documentation file of another counter,
comp_eq_overrun, as it should have its own line and not be part of
another counter's description.
Example:
$ devlink health diagnose pci/0000:00:04.0 reporter vnic
vNIC env counters:
total_error_queues: 0 send_queue_priority_update_flow: 0
comp_eq_overrun: 0 async_eq_overrun: 0 cq_overrun: 0
invalid_command: 0 quota_exceeded_command: 0
nic_receive_steering_discard: 0
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In order to allow drivers to fill all statistics, change the name
of xdo_dev_state_update_curlft to be xdo_dev_state_update_stats.
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch contains more details about the functionality
of RX copybreak.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a note when using esw_port_metadata. The parameter has runtime
mode but setting it does not take effect immediately. Setting it must
happen in legacy mode, and the port metadata takes effects when the
switchdev mode is enabled.
Disable eswitch port metadata::
$ devlink dev param set pci/0000:06:00.0 name esw_port_metadata value \
false cmode runtime
Change eswitch mode to switchdev mode where after choosing the metadata value::
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Note that other mlx5 devlink runtime parameters, esw_multiport and
flow_steering_mode, do not have this limitation.
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull documentation update from Jonathan Corbet:
"Another moderately busy cycle for documentation, including:
- The minimum Sphinx requirement has been raised to 2.4.4, following
a warning that was added in 6.2
- Some reworking of the Documentation/process front page to,
hopefully, make it more useful
- Various kernel-doc tweaks to, for example, make it deal properly
with __counted_by annotations
- We have also restored a warning for documentation of nonexistent
structure members that disappeared a while back. That had the
delightful consequence of adding some 600 warnings to the docs
build. A sustained effort by Randy, Vegard, and myself has
addressed almost all of those, bringing the documentation back into
sync with the code. The fixes are going through the appropriate
maintainer trees
- Various improvements to the HTML rendered docs, including automatic
links to Git revisions and a nice new pulldown to make translations
easy to access
- Speaking of translations, more of those for Spanish and Chinese
... plus the usual stream of documentation updates and typo fixes"
* tag 'docs-6.8' of git://git.lwn.net/linux: (57 commits)
MAINTAINERS: use tabs for indent of CONFIDENTIAL COMPUTING THREAT MODEL
A reworked process/index.rst
ring-buffer/Documentation: Add documentation on buffer_percent file
Translated the RISC-V architecture boot documentation.
Docs: remove mentions of fdformat from util-linux
Docs/zh_CN: Fix the meaning of DEBUG to pr_debug()
Documentation: move driver-api/dcdbas to userspace-api/
Documentation: move driver-api/isapnp to userspace-api/
Documentation/core-api : fix typo in workqueue
Documentation/trace: Fixed typos in the ftrace FLAGS section
kernel-doc: handle a void function without producing a warning
scripts/get_abi.pl: ignore some temp files
docs: kernel_abi.py: fix command injection
scripts/get_abi: fix source path leak
CREDITS, MAINTAINERS, docs/process/howto: Update man-pages' maintainer
docs: translations: add translations links when they exist
kernel-doc: Align quick help and the code
MAINTAINERS: add reviewer for Spanish translations
docs: ignore __counted_by attribute in structure definitions
scripts: kernel-doc: Clarify missing struct member description
..
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"The most interesting thing is probably the networking structs
reorganization and a significant amount of changes is around
self-tests.
Core & protocols:
- Analyze and reorganize core networking structs (socks, netdev,
netns, mibs) to optimize cacheline consumption and set up build
time warnings to safeguard against future header changes
This improves TCP performances with many concurrent connections up
to 40%
- Add page-pool netlink-based introspection, exposing the memory
usage and recycling stats. This helps indentify bad PP users and
possible leaks
- Refine TCP/DCCP source port selection to no longer favor even
source port at connect() time when IP_LOCAL_PORT_RANGE is set. This
lowers the time taken by connect() for hosts having many active
connections to the same destination
- Refactor the TCP bind conflict code, shrinking related socket
structs
- Refactor TCP SYN-Cookie handling, as a preparation step to allow
arbitrary SYN-Cookie processing via eBPF
- Tune optmem_max for 0-copy usage, increasing the default value to
128KB and namespecifying it
- Allow coalescing for cloned skbs coming from page pools, improving
RX performances with some common configurations
- Reduce extension header parsing overhead at GRO time
- Add bridge MDB bulk deletion support, allowing user-space to
request the deletion of matching entries
- Reorder nftables struct members, to keep data accessed by the
datapath first
- Introduce TC block ports tracking and use. This allows supporting
multicast-like behavior at the TC layer
- Remove UAPI support for retired TC qdiscs (dsmark, CBQ and ATM) and
classifiers (RSVP and tcindex)
- More data-race annotations
- Extend the diag interface to dump TCP bound-only sockets
- Conditional notification of events for TC qdisc class and actions
- Support for WPAN dynamic associations with nearby devices, to form
a sub-network using a specific PAN ID
- Implement SMCv2.1 virtual ISM device support
- Add support for Batman-avd mulicast packet type
BPF:
- Tons of verifier improvements:
- BPF register bounds logic and range support along with a large
test suite
- log improvements
- complete precision tracking support for register spills
- track aligned STACK_ZERO cases as imprecise spilled registers.
This improves the verifier "instructions processed" metric from
single digit to 50-60% for some programs
- support for user's global BPF subprogram arguments with few
commonly requested annotations for a better developer
experience
- support tracking of BPF_JNE which helps cases when the compiler
transforms (unsigned) "a > 0" into "if a == 0 goto xxx" and the
like
- several fixes
- Add initial TX metadata implementation for AF_XDP with support in
mlx5 and stmmac drivers. Two types of offloads are supported right
now, that is, TX timestamp and TX checksum offload
- Fix kCFI bugs in BPF all forms of indirect calls from BPF into
kernel and from kernel into BPF work with CFI enabled. This allows
BPF to work with CONFIG_FINEIBT=y
- Change BPF verifier logic to validate global subprograms lazily
instead of unconditionally before the main program, so they can be
guarded using BPF CO-RE techniques
- Support uid/gid options when mounting bpffs
- Add a new kfunc which acquires the associated cgroup of a task
within a specific cgroup v1 hierarchy where the latter is
identified by its id
- Extend verifier to allow bpf_refcount_acquire() of a map value
field obtained via direct load which is a use-case needed in
sched_ext
- Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter
- Support for VLAN tag in XDP hints
- Remove deprecated bpfilter kernel leftovers given the project is
developed in user-space (https://github.com/facebook/bpfilter)
Misc:
- Support for parellel TC self-tests execution
- Increase MPTCP self-tests coverage
- Updated the bridge documentation, including several so-far
undocumented features
- Convert all the net self-tests to run in unique netns, to avoid
random failures due to conflict and allow concurrent runs
- Add TCP-AO self-tests
- Add kunit tests for both cfg80211 and mac80211
- Autogenerate Netlink families documentation from YAML spec
- Add yml-gen support for fixed headers and recursive nests, the tool
can now generate user-space code for all genetlink families for
which we have specs
- A bunch of additional module descriptions fixes
- Catch incorrect freeing of pages belonging to a page pool
Driver API:
- Rust abstractions for network PHY drivers; do not cover yet the
full C API, but already allow implementing functional PHY drivers
in rust
- Introduce queue and NAPI support in the netdev Netlink interface,
allowing complete access to the device <> NAPIs <> queues
relationship
- Introduce notifications filtering for devlink to allow control
application scale to thousands of instances
- Improve PHY validation, requesting rate matching information for
each ethtool link mode supported by both the PHY and host
- Add support for ethtool symmetric-xor RSS hash
- ACPI based Wifi band RFI (WBRF) mitigation feature for the AMD
platform
- Expose pin fractional frequency offset value over new DPLL generic
netlink attribute
- Convert older drivers to platform remove callback returning void
- Add support for PHY package MMD read/write
New hardware / drivers:
- Ethernet:
- Octeon CN10K devices
- Broadcom 5760X P7
- Qualcomm SM8550 SoC
- Texas Instrument DP83TG720S PHY
- Bluetooth:
- IMC Networks Bluetooth radio
Removed:
- WiFi:
- libertas 16-bit PCMCIA support
- Atmel at76c50x drivers
- HostAP ISA/PCMCIA style 802.11b driver
- zd1201 802.11b USB dongles
- Orinoco ISA/PCMCIA 802.11b driver
- Aviator/Raytheon driver
- Planet WL3501 driver
- RNDIS USB 802.11b driver
Driver updates:
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- allow one by one port representors creation and removal
- add temperature and clock information reporting
- add get/set for ethtool's header split ringparam
- add again FW logging
- adds support switchdev hardware packet mirroring
- iavf: implement symmetric-xor RSS hash
- igc: add support for concurrent physical and free-running
timers
- i40e: increase the allowable descriptors
- nVidia/Mellanox:
- Preparation for Socket-Direct multi-dev netdev. That will
allow in future releases combining multiple PFs devices
attached to different NUMA nodes under the same netdev
- Broadcom (bnxt):
- TX completion handling improvements
- add basic ntuple filter support
- reduce MSIX vectors usage for MQPRIO offload
- add VXLAN support, USO offload and TX coalesce completion
for P7
- Marvell Octeon EP:
- xmit-more support
- add PF-VF mailbox support and use it for FW notifications
for VFs
- Wangxun (ngbe/txgbe):
- implement ethtool functions to operate pause param, ring
param, coalesce channel number and msglevel
- Netronome/Corigine (nfp):
- add flow-steering support
- support UDP segmentation offload
- Ethernet NICs embedded, slower, virtual:
- Xilinx AXI: remove duplicate DMA code adopting the dma engine
driver
- stmmac: add support for HW-accelerated VLAN stripping
- TI AM654x sw: add mqprio, frame preemption & coalescing
- gve: add support for non-4k page sizes.
- virtio-net: support dynamic coalescing moderation
- nVidia/Mellanox Ethernet datacenter switches:
- allow firmware upgrade without a reboot
- more flexible support for bridge flooding via the compressed
FID flooding mode
- Ethernet embedded switches:
- Microchip:
- fine-tune flow control and speed configurations in KSZ8xxx
- KSZ88X3: enable setting rmii reference
- Renesas:
- add jumbo frames support
- Marvell:
- 88E6xxx: add "eth-mac" and "rmon" stats support
- Ethernet PHYs:
- aquantia: add firmware load support
- at803x: refactor the driver to simplify adding support for more
chip variants
- NXP C45 TJA11xx: Add MACsec offload support
- Wifi:
- MediaTek (mt76):
- NVMEM EEPROM improvements
- mt7996 Extremely High Throughput (EHT) improvements
- mt7996 Wireless Ethernet Dispatcher (WED) support
- mt7996 36-bit DMA support
- Qualcomm (ath12k):
- support for a single MSI vector
- WCN7850: support AP mode
- Intel (iwlwifi):
- new debugfs file fw_dbg_clear
- allow concurrent P2P operation on DFS channels
- Bluetooth:
- QCA2066: support HFP offload
- ISO: more broadcast-related improvements
- NXP: better recovery in case receiver/transmitter get out of sync"
* tag 'net-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1714 commits)
lan78xx: remove redundant statement in lan78xx_get_eee
lan743x: remove redundant statement in lan743x_ethtool_get_eee
bnxt_en: Fix RCU locking for ntuple filters in bnxt_rx_flow_steer()
bnxt_en: Fix RCU locking for ntuple filters in bnxt_srxclsrldel()
bnxt_en: Remove unneeded variable in bnxt_hwrm_clear_vnic_filter()
tcp: Revert no longer abort SYN_SENT when receiving some ICMP
Revert "mlx5 updates 2023-12-20"
Revert "net: stmmac: Enable Per DMA Channel interrupt"
ipvlan: Remove usage of the deprecated ida_simple_xx() API
ipvlan: Fix a typo in a comment
net/sched: Remove ipt action tests
net: stmmac: Use interrupt mode INTM=1 for per channel irq
net: stmmac: Add support for TX/RX channel interrupt
net: stmmac: Make MSI interrupt routine generic
dt-bindings: net: snps,dwmac: per channel irq
net: phy: at803x: make read_status more generic
net: phy: at803x: add support for cdt cross short test for qca808x
net: phy: at803x: refactor qca808x cable test get status function
net: phy: at803x: generalize cdt fault length function
net: ethernet: cortina: Drop TSO support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"Many singleton patches against the MM code. The patch series which are
included in this merge do the following:
- Peng Zhang has done some mapletree maintainance work in the series
'maple_tree: add mt_free_one() and mt_attr() helpers'
'Some cleanups of maple tree'
- In the series 'mm: use memmap_on_memory semantics for dax/kmem'
Vishal Verma has altered the interworking between memory-hotplug
and dax/kmem so that newly added 'device memory' can more easily
have its memmap placed within that newly added memory.
- Matthew Wilcox continues folio-related work (including a few fixes)
in the patch series
'Add folio_zero_tail() and folio_fill_tail()'
'Make folio_start_writeback return void'
'Fix fault handler's handling of poisoned tail pages'
'Convert aops->error_remove_page to ->error_remove_folio'
'Finish two folio conversions'
'More swap folio conversions'
- Kefeng Wang has also contributed folio-related work in the series
'mm: cleanup and use more folio in page fault'
- Jim Cromie has improved the kmemleak reporting output in the series
'tweak kmemleak report format'.
- In the series 'stackdepot: allow evicting stack traces' Andrey
Konovalov to permits clients (in this case KASAN) to cause eviction
of no longer needed stack traces.
- Charan Teja Kalla has fixed some accounting issues in the page
allocator's atomic reserve calculations in the series 'mm:
page_alloc: fixes for high atomic reserve caluculations'.
- Dmitry Rokosov has added to the samples/ dorectory some sample code
for a userspace memcg event listener application. See the series
'samples: introduce cgroup events listeners'.
- Some mapletree maintanance work from Liam Howlett in the series
'maple_tree: iterator state changes'.
- Nhat Pham has improved zswap's approach to writeback in the series
'workload-specific and memory pressure-driven zswap writeback'.
- DAMON/DAMOS feature and maintenance work from SeongJae Park in the
series
'mm/damon: let users feed and tame/auto-tune DAMOS'
'selftests/damon: add Python-written DAMON functionality tests'
'mm/damon: misc updates for 6.8'
- Yosry Ahmed has improved memcg's stats flushing in the series 'mm:
memcg: subtree stats flushing and thresholds'.
- In the series 'Multi-size THP for anonymous memory' Ryan Roberts
has added a runtime opt-in feature to transparent hugepages which
improves performance by allocating larger chunks of memory during
anonymous page faults.
- Matthew Wilcox has also contributed some cleanup and maintenance
work against eh buffer_head code int he series 'More buffer_head
cleanups'.
- Suren Baghdasaryan has done work on Andrea Arcangeli's series
'userfaultfd move option'. UFFDIO_MOVE permits userspace heap
compaction algorithms to move userspace's pages around rather than
UFFDIO_COPY'a alloc/copy/free.
- Stefan Roesch has developed a 'KSM Advisor', in the series 'mm/ksm:
Add ksm advisor'. This is a governor which tunes KSM's scanning
aggressiveness in response to userspace's current needs.
- Chengming Zhou has optimized zswap's temporary working memory use
in the series 'mm/zswap: dstmem reuse optimizations and cleanups'.
- Matthew Wilcox has performed some maintenance work on the writeback
code, both code and within filesystems. The series is 'Clean up the
writeback paths'.
- Andrey Konovalov has optimized KASAN's handling of alloc and free
stack traces for secondary-level allocators, in the series 'kasan:
save mempool stack traces'.
- Andrey also performed some KASAN maintenance work in the series
'kasan: assorted clean-ups'.
- David Hildenbrand has gone to town on the rmap code. Cleanups, more
pte batching, folio conversions and more. See the series 'mm/rmap:
interface overhaul'.
- Kinsey Ho has contributed some maintenance work on the MGLRU code
in the series 'mm/mglru: Kconfig cleanup'.
- Matthew Wilcox has contributed lruvec page accounting code cleanups
in the series 'Remove some lruvec page accounting functions'"
* tag 'mm-stable-2024-01-08-15-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (361 commits)
mm, treewide: rename MAX_ORDER to MAX_PAGE_ORDER
mm, treewide: introduce NR_PAGE_ORDERS
selftests/mm: add separate UFFDIO_MOVE test for PMD splitting
selftests/mm: skip test if application doesn't has root privileges
selftests/mm: conform test to TAP format output
selftests: mm: hugepage-mmap: conform to TAP format output
selftests/mm: gup_test: conform test to TAP format output
mm/selftests: hugepage-mremap: conform test to TAP format output
mm/vmstat: move pgdemote_* out of CONFIG_NUMA_BALANCING
mm: zsmalloc: return -ENOSPC rather than -EINVAL in zs_malloc while size is too large
mm/memcontrol: remove __mod_lruvec_page_state()
mm/khugepaged: use a folio more in collapse_file()
slub: use a folio in __kmalloc_large_node
slub: use folio APIs in free_large_kmalloc()
slub: use alloc_pages_node() in alloc_slab_page()
mm: remove inc/dec lruvec page state functions
mm: ratelimit stat flush from workingset shrinker
kasan: stop leaking stack trace handles
mm/mglru: remove CONFIG_TRANSPARENT_HUGEPAGE
mm/mglru: add dummy pmd_dirty()
...
|
|
commit 23baf831a32c ("mm, treewide: redefine MAX_ORDER sanely") has
changed the definition of MAX_ORDER to be inclusive. This has caused
issues with code that was not yet upstream and depended on the previous
definition.
To draw attention to the altered meaning of the define, rename MAX_ORDER
to MAX_PAGE_ORDER.
Link: https://lkml.kernel.org/r/20231228144704.14033-2-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
e009b2efb7a8 ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
0f2b21477988 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/20240105115509.225aa8a2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 32bb4515e34469975abc936deb0a116c4a445817.
This reverts commit d078d480639a4f3b5fc2d56247afa38e0956483a.
This reverts commit fcc4b105caa4b844bf043375bf799c20a9c99db1.
This reverts commit 345237dbc1bdbb274c9fb9ec38976261ff4a40b8.
This reverts commit 7db69ec9cfb8b4ab50420262631fb2d1908b25bf.
This reverts commit 95132a018f00f5dad38bdcfd4180d1af955d46f6.
This reverts commit 63d5eaf35ac36cad00cfb3809d794ef0078c822b.
This reverts commit c29451aefcb42359905d18678de38e52eccb3bb5.
This reverts commit 2ab0edb505faa9ac90dee1732571390f074e8113.
This reverts commit dedd702a35793ab462fce4c737eeba0badf9718e.
This reverts commit 034fcc210349b873ece7356905be5c6ca11eef2a.
This reverts commit 9c5625f559ad6fe9f6f733c11475bf470e637d34.
This reverts commit 02018c544ef113e980a2349eba89003d6f399d22.
Looks like we need more time for reviews, and incremental
changes will be hard to make sense of. So revert.
Link: https://lore.kernel.org/all/ZZP6FV5sXEf+xd58@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit c902ba322cfda8ebe54ffd53392ef7e2ef5d1c65.
This reverts commit 50648968b3e3c193b45eaca07840111c9d4fdb74.
This reverts commit 77cef1e02104529f54c5b8b4126317eda3ff132d.
This reverts commit 8f8d322bc47c1c5ecab1f2238b644e30f69cc475.
This reverts commit 6ca7b5486ebd5e7985f0c98a2ac7ae49078043a4.
This reverts commit db468f92c3b9437dfeb1dcf55d9b7d1b97769a6c.
This reverts commit 5f8c64c2344c888a03fa4b7fd8c3b5e0c235d879.
This reverts commit ebdc193b2ce209bfc1ebec2f777cd7bac00b547c.
The driver needs more work.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_prog is used in receive path, both from XDP enabled drivers
and from netif_elide_gro().
This patch also removes two 4-bytes holes.
Fixes: 43a71cd66b9c ("net-device: reorganize net_device fast path variables")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240102162220.750823-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP system has a very large footprint in the driver's overall code.
makes the whole driver's code much harder to read.
Moving XDP code to dedicated files.
This patch doesn't make any changes to the code itself and only
cut-pastes the code into ena_xdp.c and ena_xdp.h files so the change
is purely cosmetic.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20240101190855.18739-2-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit had a bug and might not have been the right approach anyway.
Fixes: 629df6701c8a ("net: ipv6/addrconf: clamp preferred_lft to the minimum required")
Fixes: ec575f885e3e ("Documentation: networking: explain what happens if temp_prefered_lft is too small or too large")
Reported-by: Dan Moulding <dan@danm.net>
Closes: https://lore.kernel.org/netdev/20231221231115.12402-1-dan@danm.net/
Link: https://lore.kernel.org/netdev/CAMMLpeTdYhd=7hhPi2Y7pwdPCgnnW5JYh-bu3hSc7im39uxnEA@mail.gmail.com/
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20231230043252.10530-1-alexhenrie24@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add driver framework and device setup and initialization for Octeon
PCI Endpoint NIC VF.
Add implementation to load module, initialize, register network device,
cleanup and unload module.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev->gso_partial_features is read from tx fast path for GSO packets.
Move it to appropriate section to avoid a cache line miss.
Fixes: 43a71cd66b9c ("net-device: reorganize net_device fast path variables")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newly introduced phy_link_topology tracks all ethernet PHYs that are
attached to a netdevice. Document the base principle, internal and
external APIs. As the phy_link_topology is expected to be extended, this
documentation will hold any further improvements and additions made
relative to topology handling.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we have the ability to track the PHYs connected to a net_device
through the link_topology, we can expose this list to userspace. This
allows userspace to use these identifiers for phy-specific commands and
take the decision of which PHY to target by knowing the link topology.
Add PHY_GET and PHY_DUMP, which can be a filtered DUMP operation to list
devices on only one interface.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Linus Torvalds
Matthew Wood
David S. Miller
Jakub Kicinski
Maxime Chevallier
Tariq Toukan
Takeru Hayasaka
Haiyue Wang
Samuel Thibault
Konstantin Ryabitsev
Alex Henrie
Eric Dumazet
Nicolas Maier
Shinas Rasheed
Jinjian Song
Parav Pandit
Aahil Awatramani
Magnus Karlsson
Moshe Shemesh
Leon Romanovsky
David Arinzon
William Tu
Kirill A. Shutemov
