| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Most hw_random devices return entropy which is assumed to be of full
quality, but driver authors don't bother setting the quality knob. Some
hw_random devices return less than full quality entropy, and then driver
authors set the quality knob. Therefore, the entropy crediting should be
opt-out rather than opt-in per-driver, to reflect the actual reality on
the ground.
For example, the two Raspberry Pi RNG drivers produce full entropy
randomness, and both EDK2 and U-Boot's drivers for these treat them as
such. The result is that EFI then uses these numbers and passes the to
Linux, and Linux credits them as boot, thereby initializing the RNG.
Yet, in Linux, the quality knob was never set to anything, and so on the
chance that Linux is booted without EFI, nothing is ever credited.
That's annoying.
The same pattern appears to repeat itself throughout various drivers. In
fact, very very few drivers have bothered setting quality=1024.
Looking at the git history of existing drivers and corresponding mailing
list discussion, this conclusion tracks. There's been a decent amount of
discussion about drivers that set quality < 1024 -- somebody read and
interepreted a datasheet, or made some back of the envelope calculation
somehow. But there's been very little, if any, discussion about most
drivers where the quality is just set to 1024 or unset (or set to 1000
when the authors misunderstood the API and assumed it was base-10 rather
than base-2); in both cases the intent was fairly clear of, "this is a
hardware random device; it's fine."
So let's invert this logic. A hw_random struct's quality knob now
controls the maximum quality a driver can produce, or 0 to specify 1024.
Then, the module-wide switch called "default_quality" is changed to
represent the maximum quality of any driver. By default it's 1024, and
the quality of any particular driver is then given by:
min(default_quality, rng->quality ?: 1024);
This way, the user can still turn this off for weird reasons (and we can
replace whatever driver-specific disabling hacks existed in the past),
yet we get proper crediting for relevant RNGs.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Initialising the hwrng struct with zeros causes a
compile-time sparse warning:
$ ARCH=um make -j10 W=1 C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
...
CHECK arch/um/drivers/random.c
arch/um/drivers/random.c:31:31: sparse: warning: Using plain integer as NULL pointer
Fix the warning by not initialising the hwrng struct
with zeros as it is initialised anyway during module
init.
Fixes: 72d3e093afae ("um: random: Register random as hwrng-core device")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
We don't actually use this in um_request_irq(), so it can
never be assigned. It's also not clear what that would be
useful for, so just remove it.
This results in quite a number of cleanups, all the way to
removing the "SIGIO on close" startup check, since the data
it assigns (pty_close_sigio) is not used anymore.
While at it, also make this an enum so we get a minimum of
type checking, and remove the IRQ_NONE hack in virtio since
we now no longer have the name twice.
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
It's cumbersome and error-prone to keep adding fixed IRQ numbers,
and for proper device wakeup support for the virtio/vhost-user
support we need to have different IRQs for each device. Even if
in theory two IRQs (with and without wake) might be sufficient,
it's much easier to reason about it when we have dynamic number
assignment. It also makes it easier to add new devices that may
dynamically exist or depending on the configuration, etc.
Add support for this, up to 64 IRQs (the same limit as epoll FDs
we have right now). Since it's not easy to port all the existing
places to dynamic allocation (some data is statically initialized)
keep the low numbers are reserved for the existing hard-coded IRQ
numbers.
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The UML random driver creates a dummy device under the guest,
/dev/hw_random. When this file is read from the guest, the driver
reads from the host machine's /dev/random, in-turn reading from
the host kernel's entropy pool. This entropy pool could have been
filled by a hardware random number generator or just the host
kernel's internal software entropy generator.
Currently the driver does not fill the guests kernel entropy pool,
this requires a userspace tool running inside the guest (like
rng-tools) to read from the dummy device provided by this driver,
which then would fill the guest's internal entropy pool.
This all seems quite pointless when we are already reading from an
entropy pool, so this patch aims to register the device as a hwrng
device using the hwrng-core framework. This not only improves and
cleans up the driver, but also fills the guest's entropy pool
without having to resort to using extra userspace tools in the guest.
This is typically a nuisance when booting a guest: the random pool
takes a long time (~200s) to build up enough entropy since the dummy
hwrng is not used to fill the guest's pool.
This port was originally attempted by Alexander Neville "dark" (in CC,
discussion in Link), but the conversation there stalled since the
handling of -EAGAIN errors were no removed and longer handled by the
driver. This patch attempts to use the existing method of error
handling but utilises the new hwrng core.
The issue can be noticed when booting a UML guest:
[ 2.560000] random: fast init done
[ 214.000000] random: crng init done
With the patch applied, filling the pool becomes a lot quicker:
[ 2.560000] random: fast init done
[ 12.000000] random: crng init done
Cc: Alexander Neville <dark@volatile.bz>
Link: https://lore.kernel.org/lkml/20190828204609.02a7ff70@TheDarkness/
Link: https://lore.kernel.org/lkml/20190829135001.6a5ff940@TheDarkness.local/
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
HWRNG_MINOR and RNG_MISCDEV_MINOR are duplicate definitions, use
unified HWRNG_MINOR instead and moved into miscdevice.h
ANSLCD_MINOR and LCD_MINOR are duplicate definitions, use unified
LCD_MINOR instead and moved into miscdevice.h
MISCDEV_MINOR is renamed to PXA3XX_GCU_MINOR and moved into
miscdevice.h
Other definitions are just moved without any change.
Link: https://lore.kernel.org/lkml/20200120221323.GJ15860@mit.edu/t/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Build-tested-by: Willy TARREAU <wtarreau@haproxy.com>
Build-tested-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Link: https://lore.kernel.org/r/20200311071654.335-2-zhenzhong.duan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
reenable_fd has been a NOP since the introduction of the EPOLL
based interrupt controller.
reenable_channel() is no longer needed as the flow control is
now handled via the write IRQs on the channel.
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
1. Removes the need to walk the IRQ/Device list to determine
who triggered the IRQ.
2. Improves scalability (up to several times performance
improvement for cases with 10s of devices).
3. Improves UML baseline IO performance for one disk + one NIC
use case by up to 10%.
4. Introduces write poll triggered IRQs.
5. Prerequisite for introducing high performance mmesg family
of functions in network IO.
6. Fixes RNG shutdown which was leaking a file descriptor
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
<linux/sched.h> into <linux/sched/signal.h>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This is a nasty interface and setting the state of a foreign task must
not be done. As of the following commit:
be628be0956 ("bcache: Make gc wakeup sane, remove set_task_state()")
... everyone in the kernel calls set_task_state() with current, allowing
the helper to be removed.
However, as the comment indicates, it is still around for those archs
where computing current is more expensive than using a pointer, at least
in theory. An important arch that is affected is arm64, however this has
been addressed now [1] and performance is up to par making no difference
with either calls.
Of all the callers, if any, it's the locking bits that would care most
about this -- ie: we end up passing a tsk pointer to a lot of the lock
slowpath, and setting ->state on that. The following numbers are based
on two tests: a custom ad-hoc microbenchmark that just measures
latencies (for ~65 million calls) between get_task_state() vs
get_current_state().
Secondly for a higher overview, an unlink microbenchmark was used,
which pounds on a single file with open, close,unlink combos with
increasing thread counts (up to 4x ncpus). While the workload is quite
unrealistic, it does contend a lot on the inode mutex or now rwsem.
[1] https://lkml.kernel.org/r/1483468021-8237-1-git-send-email-mark.rutland@arm.com
== 1. x86-64 ==
Avg runtime set_task_state(): 601 msecs
Avg runtime set_current_state(): 552 msecs
vanilla dirty
Hmean unlink1-processes-2 36089.26 ( 0.00%) 38977.33 ( 8.00%)
Hmean unlink1-processes-5 28555.01 ( 0.00%) 29832.55 ( 4.28%)
Hmean unlink1-processes-8 37323.75 ( 0.00%) 44974.57 ( 20.50%)
Hmean unlink1-processes-12 43571.88 ( 0.00%) 44283.01 ( 1.63%)
Hmean unlink1-processes-21 34431.52 ( 0.00%) 38284.45 ( 11.19%)
Hmean unlink1-processes-30 34813.26 ( 0.00%) 37975.17 ( 9.08%)
Hmean unlink1-processes-48 37048.90 ( 0.00%) 39862.78 ( 7.59%)
Hmean unlink1-processes-79 35630.01 ( 0.00%) 36855.30 ( 3.44%)
Hmean unlink1-processes-110 36115.85 ( 0.00%) 39843.91 ( 10.32%)
Hmean unlink1-processes-141 32546.96 ( 0.00%) 35418.52 ( 8.82%)
Hmean unlink1-processes-172 34674.79 ( 0.00%) 36899.21 ( 6.42%)
Hmean unlink1-processes-203 37303.11 ( 0.00%) 36393.04 ( -2.44%)
Hmean unlink1-processes-224 35712.13 ( 0.00%) 36685.96 ( 2.73%)
== 2. ppc64le ==
Avg runtime set_task_state(): 938 msecs
Avg runtime set_current_state: 940 msecs
vanilla dirty
Hmean unlink1-processes-2 19269.19 ( 0.00%) 30704.50 ( 59.35%)
Hmean unlink1-processes-5 20106.15 ( 0.00%) 21804.15 ( 8.45%)
Hmean unlink1-processes-8 17496.97 ( 0.00%) 17243.28 ( -1.45%)
Hmean unlink1-processes-12 14224.15 ( 0.00%) 17240.21 ( 21.20%)
Hmean unlink1-processes-21 14155.66 ( 0.00%) 15681.23 ( 10.78%)
Hmean unlink1-processes-30 14450.70 ( 0.00%) 15995.83 ( 10.69%)
Hmean unlink1-processes-48 16945.57 ( 0.00%) 16370.42 ( -3.39%)
Hmean unlink1-processes-79 15788.39 ( 0.00%) 14639.27 ( -7.28%)
Hmean unlink1-processes-110 14268.48 ( 0.00%) 14377.40 ( 0.76%)
Hmean unlink1-processes-141 14023.65 ( 0.00%) 16271.69 ( 16.03%)
Hmean unlink1-processes-172 13417.62 ( 0.00%) 16067.55 ( 19.75%)
Hmean unlink1-processes-203 15293.08 ( 0.00%) 15440.40 ( 0.96%)
Hmean unlink1-processes-234 13719.32 ( 0.00%) 16190.74 ( 18.01%)
Hmean unlink1-processes-265 16400.97 ( 0.00%) 16115.22 ( -1.74%)
Hmean unlink1-processes-296 14388.60 ( 0.00%) 16216.13 ( 12.70%)
Hmean unlink1-processes-320 15771.85 ( 0.00%) 15905.96 ( 0.85%)
x86-64 (known to be fast for get_current()/this_cpu_read_stable() caching)
and ppc64 (with paca) show similar improvements in the unlink microbenches.
The small delta for ppc64 (2ms), does not represent the gains on the unlink
runs. In the case of x86, there was a decent amount of variation in the
latency runs, but always within a 20 to 50ms increase), ppc was more constant.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: mark.rutland@arm.com
Link: http://lkml.kernel.org/r/1483479794-14013-5-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
schedule()
schedule(), io_schedule() and schedule_timeout() always return
with TASK_RUNNING state set, so one more setting is unnecessary.
(All places in patch are visible good, only exception is
kiblnd_scheduler() from:
drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c
Its schedule() is one line above standard 3 lines of unified diff)
No places where set_current_state() is used for mb().
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1410529254.3569.23.camel@tkhai
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Anil Belur <askb23@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: David Howells <dhowells@redhat.com>
Cc: Dmitry Eremin <dmitry.eremin@intel.com>
Cc: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Isaac Huang <he.huang@intel.com>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Liang Zhen <liang.zhen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Masaru Nomura <massa.nomura@gmail.com>
Cc: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Oleg Drokin <green@linuxhacker.ru>
Cc: Peng Tao <bergwolf@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: devel@driverdev.osuosl.org
Cc: dm-devel@redhat.com
Cc: dri-devel@lists.freedesktop.org
Cc: fcoe-devel@open-fcoe.org
Cc: jfs-discussion@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-afs@lists.infradead.org
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-nfs@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: qla2xxx-upstream@qlogic.com
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: user-mode-linux-user@lists.sourceforge.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
|
|
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
|
|
cycle_kernel_lock() was added during the big BKL pushdown. It should
ensure the serializiation against driver init code. In this case there
is nothing to serialize. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <20091010153349.641118498@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
|
|
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Give random.c a style workover while I'm changing it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The random driver would essentially hang if the host's /dev/random returned
-EAGAIN. There was a test of need_resched followed by a schedule inside the
loop, but that didn't help and it's the wrong way to work anyway.
The right way is to ask for an interrupt when there is input available from
the host and handle it then rather than polling.
Now, when the host's /dev/random returns -EAGAIN, the driver asks for a wakeup
when there's randomness available again and sleeps. The interrupt routine
just wakes up whatever processes are sleeping on host_read_wait.
There is an atomic_t, host_sleep_count, which counts the number of processes
waiting for randomness. When this reaches zero, the interrupt is disabled.
An added complication is that async I/O notification was only recently added
to /dev/random (by me), so essentially all hosts will lack it. So, we use the
sigio workaround here, which is to have a separate thread poll on the
descriptor and send an interrupt when there is input on it. This mechanism is
activated when a process gets -EAGAIN (activating this multiple times is
harmless, if a bit wasteful) and deactivated by the last process still
waiting.
The module name was changed from "random" to "hw_random" in order for udev to
recognize it.
The sigio workaround needed some changes. sigio_broken was added for cases
when we know that async notification doesn't work. This is now called from
maybe_sigio_broken, which deals with pts devices.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Untangle UML headers somewhat and add some includes where they were
needed explicitly, but gotten accidentally via some other header.
arch/um/include/um_uaccess.h loses asm/fixmap.h because it uses no
fixmap stuff and gains elf.h, because it needs FIXADDR_USER_*, and
archsetjmp.h, because it needs jmp_buf.
pmd_alloc_one is uninlined because it needs mm_struct, and that's
inconvenient to provide in asm-um/pgtable-3level.h.
elf_core_copy_fpregs is also uninlined from elf-i386.h and
elf-x86_64.h, which duplicated the code anyway, to
arch/um/kernel/process.c, so that the reference to current_thread
doesn't pull sched.h or anything related into asm/elf.h.
arch/um/sys-i386/ldt.c, arch/um/kernel/tlb.c and
arch/um/kernel/skas/uaccess.c got sched.h because they dereference
task_structs. Its includes of linux and asm headers got turned from
"" to <>.
arch/um/sys-i386/bug.c gets asm/errno.h because it needs errno
constants.
asm/elf-i386 gets asm/user.h because it needs user_regs_struct.
asm/fixmap.h gets page.h because it needs PAGE_SIZE and PAGE_MASK and
system.h for BUG_ON.
asm/pgtable doesn't need sched.h.
asm/processor-generic.h defined mm_segment_t, but didn't use it. So,
that definition is moved to uaccess.h, which defines a bunch of
mm_segment_t-related stuff. thread_info.h uses mm_segment_t, and
includes uaccess.h, which causes a recursion. So, the definition is
placed above the include of thread_info. in uaccess.h. thread_info.h
also gets page.h because it needs PAGE_SIZE.
ObCheckpatchViolationJustification - I'm not adding a typedef; I'm
moving mm_segment_t from one place to another.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rename os_{read_write}_file_k back to os_{read_write}_file, delete
the originals and their bogus infrastructure, and fix all the callers.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch starts the removal of a very old, very broken piece of code. This
stems from the problem of passing a userspace buffer into read() or write() on
the host. If that buffer had not yet been faulted in, read and write will
return -EFAULT.
To avoid this problem, the solution was to fault the buffer in before the
system call by touching the pages that hold the buffer by doing a copy-user of
a byte to each page. This is obviously bogus, but it does usually work, in tt
mode, since the kernel and process are in the same address space and userspace
addresses can be accessed directly in the kernel.
In skas mode, where the kernel and process are in separate address spaces, it
is completely bogus because the userspace address, which is invalid in the
kernel, is passed into the system call instead of the corresponding physical
address, which would be valid. Here, it appears that this code, on every host
read() or write(), tries to fault in a random process page. This doesn't seem
to cause any correctness problems, but there is a performance impact. This
patch, and the ones following, result in a 10-15% performance gain on a kernel
build.
This code can't be immediately tossed out because when it is, you can't log
in. Apparently, there is some code in the console driver which depends on
this somehow.
However, we can start removing it by switching the code which does I/O using
kernel addresses to using plain read() and write(). This patch introduces
os_read_file_k and os_write_file_k for use with kernel buffers and converts
all call locations which use obvious kernel buffers to use them. These
include I/O using buffers which are local variables which are on the stack or
kmalloc-ed. Later patches will handle the less obvious cases, followed by a
mass conversion back to the original interface.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Comment the lack of locking.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some locking documentation and a cleanup. uml_exitcode is copied into a local
before sprintf sees it, in case sprintf does anything non-atomic with it.
The rest are comments about why certain globals don't need any kind of
locking.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make lots of structures const in order to make it obvious that they need no
locking.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add a MODULE_LICENSE("GPL") to the driver, remove some unused macros and add
the GPL license (it's GPL-licensed anyway since it's a GPL-derivative, apart
that Jeff Dike releases GPL software, in case anybody is wondering).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
Jason A. Donenfeld
Christopher Obbard
Johannes Berg
Zhenzhong Duan
Anton Ivanov
Ingo Molnar
Davidlohr Bueso
Linus Torvalds
Kirill Tkhai
Al Viro
Theodore Ts'o
Yong Zhang
Arnd Bergmann
Thomas Gleixner
Jeff Dike
Nishanth Aravamudan
Paolo 'Blaisorblade' Giarrusso
Linus Torvalds
