| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Fix logic that is supposed to prevent placement of the kernel image
below LOAD_PHYSICAL_ADDR
- Use the firmware stack in the EFI stub when running in mixed mode
- Clear BSS only once when using mixed mode
- Check efi.get_variable() function pointer for NULL before trying to
call it
* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: fix panic in kdump kernel
x86/efistub: Don't clear BSS twice in mixed mode
x86/efistub: Call mixed mode boot services on the firmware's stack
efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address
|
|
Check if get_next_variable() is actually valid pointer before
calling it. In kdump kernel this method is set to NULL that causes
panic during the kexec-ed kernel boot.
Tested with QEMU and OVMF firmware.
Fixes: bad267f9e18f ("efi: verify that variable services are supported")
Signed-off-by: Oleksandr Tymoshenko <ovt@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Clearing BSS should only be done once, at the very beginning.
efi_pe_entry() is the entrypoint from the firmware, which may not clear
BSS and so it is done explicitly. However, efi_pe_entry() is also used
as an entrypoint by the mixed mode startup code, in which case BSS will
already have been cleared, and doing it again at this point will corrupt
global variables holding the firmware's GDT/IDT and segment selectors.
So make the memset() conditional on whether the EFI stub is running in
native mode.
Fixes: b3810c5a2cc4a666 ("x86/efistub: Clear decompressor BSS in native EFI entrypoint")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller:
- Allow console fonts up to 64x128 pixels (Samuel Thibault)
- Prevent division-by-zero in fb monitor code (Roman Smirnov)
- Drop Renesas ARM platforms from Mobile LCDC framebuffer driver (Geert
Uytterhoeven)
- Various code cleanups in viafb, uveafb and mb862xxfb drivers by
Aleksandr Burakov, Li Zhijian and Michael Ellerman
* tag 'fbdev-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: panel-tpo-td043mtea1: Convert sprintf() to sysfs_emit()
fbmon: prevent division by zero in fb_videomode_from_videomode()
fbcon: Increase maximum font width x height to 64 x 128
fbdev: viafb: fix typo in hw_bitblt_1 and hw_bitblt_2
fbdev: mb862xxfb: Fix defined but not used error
fbdev: uvesafb: Convert sprintf/snprintf to sysfs_emit
fbdev: Restrict FB_SH_MOBILE_LCDC to SuperH
|
|
higher address
Following warning is sometimes observed while booting my servers:
[ 3.594838] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations
[ 3.602918] swapper/0: page allocation failure: order:10, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0-1
...
[ 3.851862] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocation
If 'nokaslr' boot option is set, the warning always happens.
On x86, ZONE_DMA is small zone at the first 16MB of physical address
space. When this problem happens, most of that space seems to be used by
decompressed kernel. Thereby, there is not enough space at DMA_ZONE to
meet the request of DMA pool allocation.
The commit 2f77465b05b1 ("x86/efistub: Avoid placing the kernel below
LOAD_PHYSICAL_ADDR") tried to fix this problem by introducing lower
bound of allocation.
But the fix is not complete.
efi_random_alloc() allocates pages by following steps.
1. Count total available slots ('total_slots')
2. Select a slot ('target_slot') to allocate randomly
3. Calculate a starting address ('target') to be included target_slot
4. Allocate pages, which starting address is 'target'
In step 1, 'alloc_min' is used to offset the starting address of memory
chunk. But in step 3 'alloc_min' is not considered at all. As the
result, 'target' can be miscalculated and become lower than 'alloc_min'.
When KASLR is disabled, 'target_slot' is always 0 and the problem
happens everytime if the EFI memory map of the system meets the
condition.
Fix this problem by calculating 'target' considering 'alloc_min'.
Cc: linux-efi@vger.kernel.org
Cc: Tom Englund <tomenglund26@gmail.com>
Cc: linux-kernel@vger.kernel.org
Fixes: 2f77465b05b1 ("x86/efistub: Avoid placing the kernel below LOAD_PHYSICAL_ADDR")
Signed-off-by: Kazuma Kondo <kazuma-kondo@nec.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core and kernfs changes for 6.9-rc1.
Nothing all that crazy here, just some good updates that include:
- automatic attribute group hiding from Dan Williams (he fixed up my
horrible attempt at doing this.)
- kobject lock contention fixes from Eric Dumazet
- driver core cleanups from Andy
- kernfs rcu work from Tejun
- fw_devlink changes to resolve some reported issues
- other minor changes, all details in the shortlog
All of these have been in linux-next for a long time with no reported
issues"
* tag 'driver-core-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (28 commits)
device: core: Log warning for devices pending deferred probe on timeout
driver: core: Use dev_* instead of pr_* so device metadata is added
driver: core: Log probe failure as error and with device metadata
of: property: fw_devlink: Add support for "post-init-providers" property
driver core: Add FWLINK_FLAG_IGNORE to completely ignore a fwnode link
driver core: Adds flags param to fwnode_link_add()
debugfs: fix wait/cancellation handling during remove
device property: Don't use "proxy" headers
device property: Move enum dev_dma_attr to fwnode.h
driver core: Move fw_devlink stuff to where it belongs
driver core: Drop unneeded 'extern' keyword in fwnode.h
firmware_loader: Suppress warning on FW_OPT_NO_WARN flag
sysfs:Addresses documentation in sysfs_merge_group and sysfs_unmerge_group.
firmware_loader: introduce __free() cleanup hanler
platform-msi: Remove usage of the deprecated ida_simple_xx() API
sysfs: Introduce DEFINE_SIMPLE_SYSFS_GROUP_VISIBLE()
sysfs: Document new "group visible" helpers
sysfs: Fix crash on empty group attributes array
sysfs: Introduce a mechanism to hide static attribute_groups
sysfs: Introduce a mechanism to hide static attribute_groups
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the big set of char/misc and a number of other driver
subsystem updates for 6.9-rc1. Included in here are:
- IIO driver updates, loads of new ones and evolution of existing ones
- coresight driver updates
- const cleanups for many driver subsystems
- speakup driver additions
- platform remove callback void cleanups
- mei driver updates
- mhi driver updates
- cdx driver updates for MSI interrupt handling
- nvmem driver updates
- other smaller driver updates and cleanups, full details in the
shortlog
All of these have been in linux-next for a long time with no reported
issue, other than a build warning for the speakup driver"
The build warning hits clang and is a gcc (and C23) extension, and is
fixed up in the merge.
Link: https://lore.kernel.org/all/20240321134831.GA2762840@dev-arch.thelio-3990X/
* tag 'char-misc-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (279 commits)
binder: remove redundant variable page_addr
uio_dmem_genirq: UIO_MEM_DMA_COHERENT conversion
uio_pruss: UIO_MEM_DMA_COHERENT conversion
cnic,bnx2,bnx2x: use UIO_MEM_DMA_COHERENT
uio: introduce UIO_MEM_DMA_COHERENT type
cdx: add MSI support for CDX bus
pps: use cflags-y instead of EXTRA_CFLAGS
speakup: Add /dev/synthu device
speakup: Fix 8bit characters from direct synth
parport: sunbpp: Convert to platform remove callback returning void
parport: amiga: Convert to platform remove callback returning void
char: xillybus: Convert to platform remove callback returning void
vmw_balloon: change maintainership
MAINTAINERS: change the maintainer for hpilo driver
char: xilinx_hwicap: Fix NULL vs IS_ERR() bug
hpet: remove hpets::hp_clocksource
platform: goldfish: move the separate 'default' propery for CONFIG_GOLDFISH
char: xilinx_hwicap: drop casting to void in dev_set_drvdata
greybus: move is_gb_* functions out of greybus.h
greybus: Remove usage of the deprecated ida_simple_xx() API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These update the Energy Model to make it prevent errors due to power
unit mismatches, fix a typo in power management documentation, convert
one driver to using a platform remove callback returning void, address
two cpufreq issues (one in the core and one in the DT driver), and
enable boost support in the SCMI cpufreq driver.
Specifics:
- Modify the Energy Model code to bail out and complain if the unit
of power is not uW to prevent errors due to unit mismatches (Lukasz
Luba)
- Make the intel_rapl platform driver use a remove callback returning
void (Uwe Kleine-König)
- Fix typo in the suspend and interrupts document (Saravana Kannan)
- Make per-policy boost flags actually take effect on platforms using
cpufreq_boost_set_sw() (Sibi Sankar)
- Enable boost support in the SCMI cpufreq driver (Sibi Sankar)
- Make the DT cpufreq driver use zalloc_cpumask_var() for allocating
cpumasks to avoid using unitinialized memory (Marek Szyprowski)"
* tag 'pm-6.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scmi: Enable boost support
firmware: arm_scmi: Add support for marking certain frequencies as turbo
cpufreq: dt: always allocate zeroed cpumask
cpufreq: Fix per-policy boost behavior on SoCs using cpufreq_boost_set_sw()
Documentation: power: Fix typo in suspend and interrupts doc
PM: EM: Force device drivers to provide power in uW
powercap: intel_rapl: Convert to platform remove callback returning void
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fix from Ard Biesheuvel:
"This fixes an oversight on my part in the recent EFI stub rework for
x86, which is needed to get Linux/x86 distro builds signed again for
secure boot by Microsoft. For this reason, most of this work is being
backported to v6.1, which is therefore also affected by this
regression.
- Explicitly wipe BSS in the native EFI entrypoint, so that globals
shared with the legacy decompressor are zero-initialized correctly"
* tag 'efi-fixes-for-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
x86/efistub: Clear decompressor BSS in native EFI entrypoint
|
|
By using bitmaps we actually support whatever size we would want, but
the console currently limits fonts to 64x128 (which gives 60x16 text on
4k screens), so we don't need more for now, and we can easily increase
later.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The EFI stub on x86 no longer invokes the decompressor as a subsequent
boot stage, but calls into the decompression code directly while running
in the context of the EFI boot services.
This means that when using the native EFI entrypoint (as opposed to the
EFI handover protocol, which clears BSS explicitly), the firmware PE
image loader is being relied upon to ensure that BSS is zeroed before
the EFI stub is entered from the firmware.
As Radek's report proves, this is a bad idea. Not all loaders do this
correctly, which means some global variables that should be statically
initialized to 0x0 may have junk in them.
So clear BSS explicitly when entering via efi_pe_entry(). Note that
zeroing BSS from C code is not generally safe, but in this case, the
following assignment and dereference of a global pointer variable
ensures that the memset() cannot be deferred or reordered.
Cc: <stable@kernel.org> # v6.1+
Reported-by: Radek Podgorny <radek@podgorny.cz>
Closes: https://lore.kernel.org/all/a99a831a-8ad5-4cb0-bff9-be637311f771@podgorny.cz
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge more ARM cpufreq updates for 6.9 from Viresh Kumar:
"- zero initialize a cpumask (Marek Szyprowski).
- Boost support for scmi cpufreq driver (Sibi Sankar)."
* tag 'cpufreq-arm-updates-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Enable boost support
firmware: arm_scmi: Add support for marking certain frequencies as turbo
cpufreq: dt: always allocate zeroed cpumask
|
|
All opps above the sustained frequency are treated as turbo, so mark them
accordingly.
Suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- Kuan-Wei Chiu has developed the well-named series "lib min_heap: Min
heap optimizations".
- Kuan-Wei Chiu has also sped up the library sorting code in the series
"lib/sort: Optimize the number of swaps and comparisons".
- Alexey Gladkov has added the ability for code running within an IPC
namespace to alter its IPC and MQ limits. The series is "Allow to
change ipc/mq sysctls inside ipc namespace".
- Geert Uytterhoeven has contributed some dhrystone maintenance work in
the series "lib: dhry: miscellaneous cleanups".
- Ryusuke Konishi continues nilfs2 maintenance work in the series
"nilfs2: eliminate kmap and kmap_atomic calls"
"nilfs2: fix kernel bug at submit_bh_wbc()"
- Nathan Chancellor has updated our build tools requirements in the
series "Bump the minimum supported version of LLVM to 13.0.1".
- Muhammad Usama Anjum continues with the selftests maintenance work in
the series "selftests/mm: Improve run_vmtests.sh".
- Oleg Nesterov has done some maintenance work against the signal code
in the series "get_signal: minor cleanups and fix".
Plus the usual shower of singleton patches in various parts of the tree.
Please see the individual changelogs for details.
* tag 'mm-nonmm-stable-2024-03-14-09-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (77 commits)
nilfs2: prevent kernel bug at submit_bh_wbc()
nilfs2: fix failure to detect DAT corruption in btree and direct mappings
ocfs2: enable ocfs2_listxattr for special files
ocfs2: remove SLAB_MEM_SPREAD flag usage
assoc_array: fix the return value in assoc_array_insert_mid_shortcut()
buildid: use kmap_local_page()
watchdog/core: remove sysctl handlers from public header
nilfs2: use div64_ul() instead of do_div()
mul_u64_u64_div_u64: increase precision by conditionally swapping a and b
kexec: copy only happens before uchunk goes to zero
get_signal: don't initialize ksig->info if SIGNAL_GROUP_EXIT/group_exec_task
get_signal: hide_si_addr_tag_bits: fix the usage of uninitialized ksig
get_signal: don't abuse ksig->info.si_signo and ksig->sig
const_structs.checkpatch: add device_type
Normalise "name (ad@dr)" MODULE_AUTHORs to "name <ad@dr>"
dyndbg: replace kstrdup() + strchr() with kstrdup_and_replace()
list: leverage list_is_head() for list_entry_is_head()
nilfs2: MAINTAINERS: drop unreachable project mirror site
smp: make __smp_processor_id() 0-argument macro
fat: fix uninitialized field in nostale filehandles
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Sumanth Korikkar has taught s390 to allocate hotplug-time page frames
from hotplugged memory rather than only from main memory. Series
"implement "memmap on memory" feature on s390".
- More folio conversions from Matthew Wilcox in the series
"Convert memcontrol charge moving to use folios"
"mm: convert mm counter to take a folio"
- Chengming Zhou has optimized zswap's rbtree locking, providing
significant reductions in system time and modest but measurable
reductions in overall runtimes. The series is "mm/zswap: optimize the
scalability of zswap rb-tree".
- Chengming Zhou has also provided the series "mm/zswap: optimize zswap
lru list" which provides measurable runtime benefits in some
swap-intensive situations.
- And Chengming Zhou further optimizes zswap in the series "mm/zswap:
optimize for dynamic zswap_pools". Measured improvements are modest.
- zswap cleanups and simplifications from Yosry Ahmed in the series
"mm: zswap: simplify zswap_swapoff()".
- In the series "Add DAX ABI for memmap_on_memory", Vishal Verma has
contributed several DAX cleanups as well as adding a sysfs tunable to
control the memmap_on_memory setting when the dax device is
hotplugged as system memory.
- Johannes Weiner has added the large series "mm: zswap: cleanups",
which does that.
- More DAMON work from SeongJae Park in the series
"mm/damon: make DAMON debugfs interface deprecation unignorable"
"selftests/damon: add more tests for core functionalities and corner cases"
"Docs/mm/damon: misc readability improvements"
"mm/damon: let DAMOS feeds and tame/auto-tune itself"
- In the series "mm/mempolicy: weighted interleave mempolicy and sysfs
extension" Rakie Kim has developed a new mempolicy interleaving
policy wherein we allocate memory across nodes in a weighted fashion
rather than uniformly. This is beneficial in heterogeneous memory
environments appearing with CXL.
- Christophe Leroy has contributed some cleanup and consolidation work
against the ARM pagetable dumping code in the series "mm: ptdump:
Refactor CONFIG_DEBUG_WX and check_wx_pages debugfs attribute".
- Luis Chamberlain has added some additional xarray selftesting in the
series "test_xarray: advanced API multi-index tests".
- Muhammad Usama Anjum has reworked the selftest code to make its
human-readable output conform to the TAP ("Test Anything Protocol")
format. Amongst other things, this opens up the use of third-party
tools to parse and process out selftesting results.
- Ryan Roberts has added fork()-time PTE batching of THP ptes in the
series "mm/memory: optimize fork() with PTE-mapped THP". Mainly
targeted at arm64, this significantly speeds up fork() when the
process has a large number of pte-mapped folios.
- David Hildenbrand also gets in on the THP pte batching game in his
series "mm/memory: optimize unmap/zap with PTE-mapped THP". It
implements batching during munmap() and other pte teardown
situations. The microbenchmark improvements are nice.
- And in the series "Transparent Contiguous PTEs for User Mappings"
Ryan Roberts further utilizes arm's pte's contiguous bit ("contpte
mappings"). Kernel build times on arm64 improved nicely. Ryan's
series "Address some contpte nits" provides some followup work.
- In the series "mm/hugetlb: Restore the reservation" Breno Leitao has
fixed an obscure hugetlb race which was causing unnecessary page
faults. He has also added a reproducer under the selftest code.
- In the series "selftests/mm: Output cleanups for the compaction
test", Mark Brown did what the title claims.
- Kinsey Ho has added the series "mm/mglru: code cleanup and
refactoring".
- Even more zswap material from Nhat Pham. The series "fix and extend
zswap kselftests" does as claimed.
- In the series "Introduce cpu_dcache_is_aliasing() to fix DAX
regression" Mathieu Desnoyers has cleaned up and fixed rather a mess
in our handling of DAX on archiecctures which have virtually aliasing
data caches. The arm architecture is the main beneficiary.
- Lokesh Gidra's series "per-vma locks in userfaultfd" provides
dramatic improvements in worst-case mmap_lock hold times during
certain userfaultfd operations.
- Some page_owner enhancements and maintenance work from Oscar Salvador
in his series
"page_owner: print stacks and their outstanding allocations"
"page_owner: Fixup and cleanup"
- Uladzislau Rezki has contributed some vmalloc scalability
improvements in his series "Mitigate a vmap lock contention". It
realizes a 12x improvement for a certain microbenchmark.
- Some kexec/crash cleanup work from Baoquan He in the series "Split
crash out from kexec and clean up related config items".
- Some zsmalloc maintenance work from Chengming Zhou in the series
"mm/zsmalloc: fix and optimize objects/page migration"
"mm/zsmalloc: some cleanup for get/set_zspage_mapping()"
- Zi Yan has taught the MM to perform compaction on folios larger than
order=0. This a step along the path to implementaton of the merging
of large anonymous folios. The series is named "Enable >0 order folio
memory compaction".
- Christoph Hellwig has done quite a lot of cleanup work in the
pagecache writeback code in his series "convert write_cache_pages()
to an iterator".
- Some modest hugetlb cleanups and speedups in Vishal Moola's series
"Handle hugetlb faults under the VMA lock".
- Zi Yan has changed the page splitting code so we can split huge pages
into sizes other than order-0 to better utilize large folios. The
series is named "Split a folio to any lower order folios".
- David Hildenbrand has contributed the series "mm: remove
total_mapcount()", a cleanup.
- Matthew Wilcox has sought to improve the performance of bulk memory
freeing in his series "Rearrange batched folio freeing".
- Gang Li's series "hugetlb: parallelize hugetlb page init on boot"
provides large improvements in bootup times on large machines which
are configured to use large numbers of hugetlb pages.
- Matthew Wilcox's series "PageFlags cleanups" does that.
- Qi Zheng's series "minor fixes and supplement for ptdesc" does that
also. S390 is affected.
- Cleanups to our pagemap utility functions from Peter Xu in his series
"mm/treewide: Replace pXd_large() with pXd_leaf()".
- Nico Pache has fixed a few things with our hugepage selftests in his
series "selftests/mm: Improve Hugepage Test Handling in MM
Selftests".
- Also, of course, many singleton patches to many things. Please see
the individual changelogs for details.
* tag 'mm-stable-2024-03-13-20-04' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (435 commits)
mm/zswap: remove the memcpy if acomp is not sleepable
crypto: introduce: acomp_is_async to expose if comp drivers might sleep
memtest: use {READ,WRITE}_ONCE in memory scanning
mm: prohibit the last subpage from reusing the entire large folio
mm: recover pud_leaf() definitions in nopmd case
selftests/mm: skip the hugetlb-madvise tests on unmet hugepage requirements
selftests/mm: skip uffd hugetlb tests with insufficient hugepages
selftests/mm: dont fail testsuite due to a lack of hugepages
mm/huge_memory: skip invalid debugfs new_order input for folio split
mm/huge_memory: check new folio order when split a folio
mm, vmscan: retry kswapd's priority loop with cache_trim_mode off on failure
mm: add an explicit smp_wmb() to UFFDIO_CONTINUE
mm: fix list corruption in put_pages_list
mm: remove folio from deferred split list before uncharging it
filemap: avoid unnecessary major faults in filemap_fault()
mm,page_owner: drop unnecessary check
mm,page_owner: check for null stack_record before bumping its refcount
mm: swap: fix race between free_swap_and_cache() and swapoff()
mm/treewide: align up pXd_leaf() retval across archs
mm/treewide: drop pXd_large()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This was a relatively calm development cycle. Most of changes are
rather small device-specific fixes and enhancements. The only
significant changes in ALSA core are code refactoring with the recent
cleanup infrastructure, which should bring no functionality changes.
Some highlights below:
Core:
- Lots of cleanups in ALSA core code with automatic kfree cleanup and
locking guard macros
- New ALSA core kunit test
ASoC:
- SoundWire support for AMD ACP 6.3 systems
- Support for reporting version information for AVS firmware
- Support DSPless mode for Intel Soundwire systems
- Support for configuring CS35L56 amplifiers using EFI calibration
data
- Log which component is being operated on as part of power
management trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
HD- and USB-audio:
- More Cirrus HD-audio codec support
- TAS2781 HD-audio codec fixes
- Scarlett2 mixer fixes
Others:
- Enhancement of virtio driver for audio control supports
- Cleanups of legacy PM code with new macros
- Firewire sound updates"
* tag 'sound-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (307 commits)
ALSA: usb-audio: Stop parsing channels bits when all channels are found.
ALSA: hda/tas2781: remove unnecessary runtime_pm calls
ALSA: hda/realtek - ALC236 fix volume mute & mic mute LED on some HP models
ALSA: aaci: Delete unused variable in aaci_do_suspend
ALSA: scarlett2: Fix Scarlett 4th Gen input gain range again
ALSA: scarlett2: Fix Scarlett 4th Gen input gain range
ALSA: scarlett2: Fix Scarlett 4th Gen autogain status values
ALSA: scarlett2: Fix Scarlett 4th Gen 4i4 low-voltage detection
ALSA: hda/tas2781: restore power state after system_resume
ALSA: hda/tas2781: do not call pm_runtime_force_* in system_resume/suspend
ALSA: hda/tas2781: do not reset cur_* values in runtime_suspend
ALSA: hda/tas2781: add lock to system_suspend
ALSA: hda/tas2781: use dev_dbg in system_resume
ALSA: hda/realtek: fix ALC285 issues on HP Envy x360 laptops
platform/x86: serial-multi-instantiate: Add support for CS35L54 and CS35L57
ALSA: hda: cs35l56: Add support for CS35L54 and CS35L57
ASoC: cs35l56: Add support for CS35L54 and CS35L57
ASoC: Intel: catpt: Carefully use PCI bitwise constants
ALSA: hda: hda_component: Include sound/hda_codec.h
ALSA: hda: hda_component: Add missing #include guards
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate interrupt related code in irq.c (Ilpo Järvinen)
- Reduce kernel size by replacing sysfs resource macros with
functions (Ilpo Järvinen)
- Reduce kernel size by compiling sysfs support only when
CONFIG_SYSFS=y (Lukas Wunner)
- Avoid using Extended Tags on 3ware-9650SE Root Port to work around
an apparent hardware defect (Jörg Wedekind)
Resource management:
- Fix an MMIO mapping leak in pci_iounmap() (Philipp Stanner)
- Move pci_iomap.c and other PCI-specific devres code to drivers/pci
(Philipp Stanner)
- Consolidate PCI devres code in devres.c (Philipp Stanner)
Power management:
- Avoid D3cold on Asus B1400 PCI-NVMe bridge, where firmware doesn't
know how to return correctly to D0, and remove previous quirk that
wasn't as specific (Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any
runtime PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races
between .remove() and .runtime_idle(), which caused intermittent
page faults when the rtsx .runtime_idle() accessed registers that
its .remove() had already unmapped (Rafael J. Wysocki)
Virtualization:
- Avoid Secondary Bus Reset on LSI FW643 so it can be assigned to VMs
with VFIO, e.g., for professional audio software on many Apple
machines, at the cost of leaking state between VMs (Edmund Raile)
Error handling:
- Print all logged TLP Prefixes, not just the first, after AER or DPC
errors (Ilpo Järvinen)
- Quirk the DPC PIO log size for Intel Raptor Lake Root Ports, which
still don't advertise a legal size (Paul Menzel)
- Ignore expected DPC Surprise Down errors on hot removal (Smita
Koralahalli)
- Block runtime suspend while handling AER errors to avoid races that
prevent the device form being resumed from D3hot (Stanislaw
Gruszka)
Peer-to-peer DMA:
- Use atomic XA allocation in RCU read section (Christophe JAILLET)
ASPM:
- Collect bits of ASPM-related code that we need even without
CONFIG_PCIEASPM into aspm.c (David E. Box)
- Save/restore L1 PM Substates config for suspend/resume (David E.
Box)
- Update save_save when ASPM config is changed, so a .slot_reset()
during error recovery restores the changed config, not the
.probe()-time config (Vidya Sagar)
Endpoint framework:
- Refactor and improve pci_epf_alloc_space() API (Niklas Cassel)
- Clean up endpoint BAR descriptions (Niklas Cassel)
- Fix ntb_register_device() name leak in error path (Yang Yingliang)
- Return actual error code for pci_vntb_probe() failure (Yang
Yingliang)
Broadcom STB PCIe controller driver:
- Fix MDIO write polling, which previously never waited for
completion (Jonathan Bell)
Cadence PCIe endpoint driver:
- Clear the ARI "Next Function Number" of last function (Jasko-EXT
Wojciech)
Freescale i.MX6 PCIe controller driver:
- Simplify by replacing switch statements with function pointers for
different hardware variants (Frank Li)
- Simplify by using clk_bulk*() API (Frank Li)
- Remove redundant DT clock and reg/reg-name details (Frank Li)
- Add i.MX95 DT and driver support for both Root Complex and Endpoint
mode (Frank Li)
Microsoft Hyper-V host bridge driver:
- Reduce memory usage by limiting ring buffer size to 16KB instead of
4 pages (Michael Kelley)
Qualcomm PCIe controller driver:
- Add X1E80100 DT and driver support (Abel Vesa)
- Add DT 'required-opps' for SoCs that require a minimum performance
level (Johan Hovold)
- Make DT 'msi-map-mask' optional, depending on how MSI interrupts
are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because the PHY
configuration isn't tuned correctly for L0s (Johan Hovold)
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and
separate files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150,
SM8250, SM8350, SM8450, SM8550 for easier reviewing (Krzysztof
Kozlowski)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add endpoint MHI support for Snapdragon SA8775P SoC (Mrinmay
Sarkar)
Synopsys DesignWare PCIe controller driver:
- Allocate 64-bit MSI address if no 32-bit address is available (Ajay
Agarwal)
- Fix endpoint Resizable BAR to actually advertise the required 1MB
size (Niklas Cassel)
MicroSemi Switchtec management driver:
- Release resources if the .probe() fails (Christophe JAILLET)
Miscellaneous:
- Make pcie_port_bus_type const (Ricardo B. Marliere)"
* tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (77 commits)
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI: hv: Fix ring buffer size calculation
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: cadence: Clear the ARI Capability Next Function Number of the last function
PCI: dwc: Strengthen the MSI address allocation logic
PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI/AER: Generalize TLP Header Log reading
PCI/AER: Use explicit register size for PCI_ERR_CAP
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
PCI/AER: Block runtime suspend when handling errors
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
...
|
|
Pull drm updates from Dave Airlie:
"Highlights are usual, more AMD IP blocks for future hw, i915/xe
changes, Displayport tunnelling support for i915, msm YUV over DP
changes, new tests for ttm, but its mostly a lot of stuff all over the
place from lots of people.
core:
- EDID cleanups
- scheduler error handling fixes
- managed: add drmm_release_action() with tests
- add ratelimited drm debug print
- DPCD PSR early transport macro
- DP tunneling and bandwidth allocation helpers
- remove built-in edids
- dp: Avoid AUX transfers on powered-down displays
- dp: Add VSC SDP helpers
cross drivers:
- use new drm print helpers
- switch to ->read_edid callback
- gem: add stats for shared buffers plus updates to amdgpu, i915, xe
syncobj:
- fixes to waiting and sleeping
ttm:
- add tests
- fix errno codes
- simply busy-placement handling
- fix page decryption
media:
- tc358743: fix v4l device registration
video:
- move all kernel parameters for video behind CONFIG_VIDEO
sound:
- remove <drm/drm_edid.h> include from header
ci:
- add tests for msm
- fix apq8016 runner
efifb:
- use copy of global screen_info state
vesafb:
- use copy of global screen_info state
simplefb:
- fix logging
bridge:
- ite-6505: fix DP link-training bug
- samsung-dsim: fix error checking in probe
- samsung-dsim: add bsh-smm-s2/pro boards
- tc358767: fix regmap usage
- imx: add i.MX8MP HDMI PVI plus DT bindings
- imx: add i.MX8MP HDMI TX plus DT bindings
- sii902x: fix probing and unregistration
- tc358767: limit pixel PLL input range
- switch to new drm_bridge_read_edid() interface
panel:
- ltk050h3146w: error-handling fixes
- panel-edp: support delay between power-on and enable; use put_sync
in unprepare; support Mediatek MT8173 Chromebooks, BOE NV116WHM-N49
V8.0, BOE NV122WUM-N41, CSO MNC207QS1-1 plus DT bindings
- panel-lvds: support EDT ETML0700Z9NDHA plus DT bindings
- panel-novatek: FRIDA FRD400B25025-A-CTK plus DT bindings
- add BOE TH101MB31IG002-28A plus DT bindings
- add EDT ETML1010G3DRA plus DT bindings
- add Novatek NT36672E LCD DSI plus DT bindings
- nt36523: support 120Hz timings, fix includes
- simple: fix display timings on RK32FN48H
- visionox-vtdr6130: fix initialization
- add Powkiddy RGB10MAX3 plus DT bindings
- st7703: support panel rotation plus DT bindings
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
panel-orientation-quirks:
- GPD Win Mini
amdgpu:
- Validate DMABuf imports in compute VMs
- Add RAS ACA framework
- PSP 13 fixes
- Misc code cleanups
- Replay fixes
- Atom interpretor PS, WS bounds checking
- DML2 fixes
- Audio fixes
- DCN 3.5 Z state fixes
- Remove deprecated ida_simple usage
- UBSAN fixes
- RAS fixes
- Enable seq64 infrastructure
- DC color block enablement
- Documentation updates
- DC documentation updates
- DMCUB updates
- ATHUB 4.1 support
- LSDMA 7.0 support
- JPEG DPG support
- IH 7.0 support
- HDP 7.0 support
- VCN 5.0 support
- SMU 13.0.6 updates
- NBIO 7.11 updates
- SDMA 6.1 updates
- MMHUB 3.3 updates
- DCN 3.5.1 support
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Validate DMABuf imports in compute VMs
- SVM fixes
- Trap handler updates and enhancements
- Fix cache size reporting
- Relocate the trap handler
radeon:
- Atom interpretor PS, WS bounds checking
- Misc code cleanups
xe:
- new query for GuC submission version
- Remove unused persistent exec_queues
- Add vram frequency sysfs attributes
- Add the flag XE_VM_BIND_FLAG_DUMPABLE
- Drop pre-production workarounds
- Drop kunit tests for unsupported platforms
- Start pumbling SR-IOV support with memory based interrupts for VF
- Allow to map BO in GGTT with PAT index corresponding to XE_CACHE_UC
to work with memory based interrupts
- Add GuC Doorbells Manager as prep work SR-IOV
- Implement additional workarounds for xe2 and MTL
- Program a few registers according to perfomance guide spec for Xe2
- Fix remaining 32b build issues and enable it back
- Fix build with CONFIG_DEBUG_FS=n
- Fix warnings from GuC ABI headers
- Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF
- Release mmap mappings on rpm suspend
- Disable mid-thread preemption when not properly supported by
hardware
- Fix xe_exec by reserving extra fence slot for CPU bind
- Fix xe_exec with full long running exec queue
- Canonicalize addresses where needed for Xe2 and add to devcoredum
- Toggle USM support for Xe2
- Only allow 1 ufence per exec / bind IOCTL
- Add GuC firmware loading for Lunar Lake
- Add XE_VMA_PTE_64K VMA flag
i915:
- Add more ADL-N PCI IDs
- Enable fastboot also on older platforms
- Early transport for panel replay and PSR
- New ARL PCI IDs
- DP TPS4 PHY test pattern support
- Unify and improve VSC SDP for PSR and non-PSR cases
- Refactor memory regions and improve debug logging
- Rework global state serialization
- Remove unused CDCLK divider fields
- Unify HDCP connector logging format
- Use display instead of graphics version in display code
- Move VBT and opregion debugfs next to the implementation
- Abstract opregion interface, use opaque type
- MTL fixes
- HPD handling fixes
- Add GuC submission interface version query
- Atomically invalidate userptr on mmu-notifier
- Update handling of MMIO triggered reports
- Don't make assumptions about intel_wakeref_t type
- Extend driver code of Xe_LPG to Xe_LPG+
- Add flex arrays to struct i915_syncmap
- Allow for very slow HuC loading
- DP tunneling and bandwidth allocation support
msm:
- Correct bindings for MSM8976 and SM8650 platforms
- Start migration of MDP5 platforms to DPU driver
- X1E80100 MDSS support
- DPU:
- Improve DSC allocation, fixing several important corner cases
- Add support for SDM630/SDM660 platforms
- Simplify dpu_encoder_phys_ops
- Apply fixes targeting DSC support with a single DSC encoder
- Apply fixes for HCTL_EN timing configuration
- X1E80100 support
- Add support for YUV420 over DP
- GPU:
- fix sc7180 UBWC config
- fix a7xx LLC config
- new gpu support: a305B, a750, a702
- machine support: SM7150 (different power levels than other a618)
- a7xx devcoredump support
habanalabs:
- configure IRQ affinity according to NUMA node
- move HBM MMU page tables inside the HBM
- improve device reset
- check extended PCIe errors
ivpu:
- updates to firmware API
- refactor BO allocation
imx:
- use devm_ functions during init
hisilicon:
- fix EDID includes
mgag200:
- improve ioremap usage
- convert to struct drm_edid
- Work around PCI write bursts
nouveau:
- disp: use kmemdup()
- fix EDID includes
- documentation fixes
qaic:
- fixes to BO handling
- make use of DRM managed release
- fix order of remove operations
rockchip:
- analogix_dp: get encoder port from DT
- inno_hdmi: support HDMI for RK3128
- lvds: error-handling fixes
ssd130x:
- support SSD133x plus DT bindings
tegra:
- fix error handling
tilcdc:
- make use of DRM managed release
v3d:
- show memory stats in debugfs
- Support display MMU page size
vc4:
- fix error handling in plane prepare_fb
- fix framebuffer test in plane helpers
virtio:
- add venus capset defines
vkms:
- fix OOB access when programming the LUT
- Kconfig improvements
vmwgfx:
- unmap surface before changing plane state
- fix memory leak in error handling
- documentation fixes
- list command SVGA_3D_CMD_DEFINE_GB_SURFACE_V4 as invalid
- fix null-pointer deref in execbuf
- refactor display-mode probing
- fix fencing for creating cursor MOBs
- fix cursor-memory lifetime
xlnx:
- fix live video input for ZynqMP DPSUB
lima:
- fix memory leak
loongson:
- fail if no VRAM present
meson:
- switch to new drm_bridge_read_edid() interface
renesas:
- add RZ/G2L DU support plus DT bindings
mxsfb:
- Use managed mode config
sun4i:
- HDMI: updates to atomic mode setting
mediatek:
- Add display driver for MT8188 VDOSYS1
- DSI driver cleanups
- Filter modes according to hardware capability
- Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
etnaviv:
- enhancements for NPU and MRT support"
* tag 'drm-next-2024-03-13' of https://gitlab.freedesktop.org/drm/kernel: (1420 commits)
drm/amd/display: Removed redundant @ symbol to fix kernel-doc warnings in -next repo
drm/amd/pm: wait for completion of the EnableGfxImu message
drm/amdgpu/soc21: add mode2 asic reset for SMU IP v14.0.1
drm/amdgpu: add smu 14.0.1 support
drm/amdgpu: add VPE 6.1.1 discovery support
drm/amdgpu/vpe: add VPE 6.1.1 support
drm/amdgpu/vpe: don't emit cond exec command under collaborate mode
drm/amdgpu/vpe: add collaborate mode support for VPE
drm/amdgpu/vpe: add PRED_EXE and COLLAB_SYNC OPCODE
drm/amdgpu/vpe: add multi instance VPE support
drm/amdgpu/discovery: add nbif v6_3_1 ip block
drm/amdgpu: Add nbif v6_3_1 ip block support
drm/amdgpu: Add pcie v6_1_0 ip headers (v5)
drm/amdgpu: Add nbif v6_3_1 ip headers (v5)
arch/powerpc: Remove <linux/fb.h> from backlight code
macintosh/via-pmu-backlight: Include <linux/backlight.h>
fbdev/chipsfb: Include <linux/backlight.h>
drm/etnaviv: Restore some id values
drm/amdkfd: make kfd_class constant
drm/amdgpu: add ring timeout information in devcoredump
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI updates from Ard Biesheuvel:
- Measure initrd and command line using the CC protocol if the ordinary
TCG2 protocol is not implemented, typically on TDX confidential VMs
- Avoid creating mappings that are both writable and executable while
running in the EFI boot services. This is a prerequisite for getting
the x86 shim loader signed by MicroSoft again, which allows the
distros to install on x86 PCs that ship with EFI secure boot enabled.
- API update for struct platform_driver::remove()
* tag 'efi-next-for-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
virt: efi_secret: Convert to platform remove callback returning void
x86/efistub: Remap kernel text read-only before dropping NX attribute
efi/libstub: Add get_event_log() support for CC platforms
efi/libstub: Measure into CC protocol if TCG2 protocol is absent
efi/libstub: Add Confidential Computing (CC) measurement typedefs
efi/tpm: Use symbolic GUID name from spec for final events table
efi/libstub: Use TPM event typedefs from the TCG PC Client spec
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"From the functional perspective, the most significant change here is
the addition of support for Energy Models that can be updated
dynamically at run time.
There is also the addition of LZ4 compression support for hibernation,
the new preferred core support in amd-pstate, new platforms support in
the Intel RAPL driver, new model-specific EPP handling in intel_pstate
and more.
Apart from that, the cpufreq default transition delay is reduced from
10 ms to 2 ms (along with some related adjustments), the system
suspend statistics code undergoes a significant rework and there is a
usual bunch of fixes and code cleanups all over.
Specifics:
- Allow the Energy Model to be updated dynamically (Lukasz Luba)
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V)
- Fix and clean up system suspend statistics collection (Rafael
Wysocki)
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki)
- Fix PCI hibernation support description (Yiwei Lin)
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy)
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah)
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li)
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus)
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat)
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin)
- Enable preferred core support in the amd-pstate cpufreq driver
(Meng Li)
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li)
- Allow intel_pstate to assign model-specific values to strings used
in the EPP sysfs interface and make it do so on Meteor Lake
(Srinivas Pandruvada)
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby)
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar)
- Change default transition delay in cpufreq to 2ms (Qais Yousef)
- Remove references to 10ms minimum sampling rate from comments in
the cpufreq code (Pierre Gondois)
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef)
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar)
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova)
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan)
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois)
- Prevent the haltpoll cpuidle governor from shrinking guest
poll_limit_ns below grow_start (Parshuram Sangle)
- Avoid potential overflow in integer multiplication when computing
cpuidle state parameters (C Cheng)
- Adjust MWAIT hint target C-state computation in the ACPI cpuidle
driver and in intel_idle to return a correct value for C0 (He
Rongguang)
- Address multiple issues in the TPMI RAPL driver and add support for
new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui)
- Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
Lezcano)
- Fix kernel-doc for dtpm_create_hierarchy() (Yang Li)
- Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
Norway Ananda)
- Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil)
- Fix a couple of warnings in the OPP core code related to W=1 builds
(Viresh Kumar)
- Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh
Kumar)
- Extend dev_pm_opp_data with turbo support (Sibi Sankar)
- dt-bindings: drop maxItems from inner items (David Heidelberg)"
* tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (95 commits)
dt-bindings: opp: drop maxItems from inner items
OPP: debugfs: Fix warning around icc_get_name()
OPP: debugfs: Fix warning with W=1 builds
cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h
OPP: Extend dev_pm_opp_data with turbo support
Fix cpupower-frequency-info.1 man page typo
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpuidle: ACPI/intel: fix MWAIT hint target C-state computation
PM: sleep: wakeirq: fix wake irq warning in system suspend
powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function
cpufreq: Don't unregister cpufreq cooling on CPU hotplug
PM: suspend: Set mem_sleep_current during kernel command line setup
cpufreq: Honour transition_latency over transition_delay_us
cpufreq: Limit resolving a frequency to policy min/max
Documentation: PM: Fix runtime_pm.rst markdown syntax
cpufreq: amd-pstate: adjust min/max limit perf
cpufreq: Remove references to 10ms min sampling rate
cpufreq: intel_pstate: Update default EPPs for Meteor Lake
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform firmware updates from Tzung-Bi Shih:
- Allow userspace to automatically load coreboot modules by adding
modaliases and sending uevents
- Make bus_type const
* tag 'tag-chrome-platform-firmware-for-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
firmware: coreboot: Replace tag with id table in driver struct
firmware: coreboot: Generate aliases for coreboot modules
firmware: coreboot: Generate modalias uevent for devices
firmware: coreboot: make coreboot_bus_type const
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
- Make PSTORE_RAM available by default on arm64 (Nícolas F R A Prado)
- Allow for dynamic initialization in modular build (Guilherme G
Piccoli)
- Add missing allocation failure check (Kunwu Chan)
- Avoid duplicate memory zeroing (Christophe JAILLET)
- Avoid potential double-free during pstorefs umount
* tag 'pstore-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/zone: Don't clear memory twice
pstore/zone: Add a null pointer check to the psz_kmsg_read
efi: pstore: Allow dynamic initialization based on module parameter
arm64: defconfig: Enable PSTORE_RAM
pstore/ram: Register to module device table
pstore: inode: Only d_invalidate() is needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This is the usual mix of updates for drivers that are used on (mostly
ARM) SoCs with no other top-level subsystem tree, including:
- The SCMI firmware subsystem gains support for version 3.2 of the
specification and updates to the notification code
- Feature updates for Tegra and Qualcomm platforms for added hardware
support
- A number of platforms get soc_device additions for identifying
newly added chips from Renesas, Qualcomm, Mediatek and Google
- Trivial improvements for firmware and memory drivers amongst
others, in particular 'const' annotations throughout multiple
subsystems"
* tag 'soc-drivers-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
tee: make tee_bus_type const
soc: qcom: aoss: add missing kerneldoc for qmp members
soc: qcom: geni-se: drop unused kerneldoc struct geni_wrapper param
soc: qcom: spm: fix building with CONFIG_REGULATOR=n
bus: ti-sysc: constify the struct device_type usage
memory: stm32-fmc2-ebi: keep power domain on
memory: stm32-fmc2-ebi: add MP25 RIF support
memory: stm32-fmc2-ebi: add MP25 support
memory: stm32-fmc2-ebi: check regmap_read return value
dt-bindings: memory-controller: st,stm32: add MP25 support
dt-bindings: bus: imx-weim: convert to YAML
watchdog: s3c2410_wdt: use exynos_get_pmu_regmap_by_phandle() for PMU regs
soc: samsung: exynos-pmu: Add regmap support for SoCs that protect PMU regs
MAINTAINERS: Update SCMI entry with HWMON driver
MAINTAINERS: samsung: gs101: match patches touching Google Tensor SoC
memory: tegra: Fix indentation
memory: tegra: Add BPMP and ICC info for DLA clients
memory: tegra: Correct DLA client names
dt-bindings: memory: renesas,rpc-if: Document R-Car V4M support
firmware: arm_scmi: Update the supported clock protocol version
...
|
|
There's a new conflict with Linus's upstream tree, because
in the following merge conflict resolution in <asm/coco.h>:
38b334fc767e Merge tag 'x86_sev_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Linus has resolved the conflicting placement of 'cc_mask' better
than the original commit:
1c811d403afd x86/sev: Fix position dependent variable references in startup code
... which was also done by an internal merge resolution:
2e5fc4786b7a Merge branch 'x86/sev' into x86/boot, to resolve conflicts and to pick up dependent tree
But Linus is right in 38b334fc767e, the 'cc_mask' declaration is sufficient
within the #ifdef CONFIG_ARCH_HAS_CC_PLATFORM block.
So instead of forcing Linus to do the same resolution again, merge in Linus's
tree and follow his conflict resolution.
Conflicts:
arch/x86/include/asm/coco.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.9 from Viresh Kumar:
"- General enhancements / cleanups to cpufreq drivers (tianyu2, Nícolas
F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- scmi: get transition delay from firmware (Pierre Gondois)."
* tag 'cpufreq-arm-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpufreq: qcom-hw: add CONFIG_COMMON_CLK dependency
cpufreq: dt-platdev: block SDM670 in cpufreq-dt-platdev
cpufreq: mediatek-hw: Don't error out if supply is not found
Documentation: power: Use kcalloc() instead of kzalloc()
cpufreq: mediatek-hw: Wait for CPU supplies before probing
cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
cpufreq: imx6: use regmap to read ocotp register
|
|
Currently, the EFI stub invokes the EFI memory attributes protocol to
strip any NX restrictions from the entire loaded kernel, resulting in
all code and data being mapped read-write-execute.
The point of the EFI memory attributes protocol is to remove the need
for all memory allocations to be mapped with both write and execute
permissions by default, and make it the OS loader's responsibility to
transition data mappings to code mappings where appropriate.
Even though the UEFI specification does not appear to leave room for
denying memory attribute changes based on security policy, let's be
cautious and avoid relying on the ability to create read-write-execute
mappings. This is trivially achievable, given that the amount of kernel
code executing via the firmware's 1:1 mapping is rather small and
limited to the .head.text region. So let's drop the NX restrictions only
on that subregion, but not before remapping it as read-only first.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
To allow event log info access after boot, EFI boot stub extracts
the event log information and installs it in an EFI configuration
table. Currently, EFI boot stub only supports installation of event
log only for TPM 1.2 and TPM 2.0 protocols. Extend the same support
for CC protocol. Since CC platform also uses TCG2 format, reuse TPM2
support code as much as possible.
Link: https://uefi.org/specs/UEFI/2.10/38_Confidential_Computing.html#efi-cc-measurement-protocol [1]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lkml.kernel.org/r/0229a87e-fb19-4dad-99fc-4afd7ed4099a%40collabora.com
[ardb: Split out final events table handling to avoid version confusion]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
To accommodate confidential compute VMs that expose the simplified CC
measurement protocol instead of the full-blown TCG2 one, fall back to
the former if the latter does not exist.
The CC protocol was designed to be used in this manner, which is why the
types and prototypes have been kept the same where possible. So reuse
the existing code, and only deviate from the TCG2 code path where
needed.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
If the virtual firmware implements TPM support, TCG2 protocol will be
used for kernel measurements and event logging support. But in CC
environment, not all platforms support or enable the TPM feature. UEFI
specification [1] exposes protocol and interfaces used for kernel
measurements in CC platforms without TPM support.
More details about the EFI CC measurements and logging can be found
in [1].
Link: https://uefi.org/specs/UEFI/2.10/38_Confidential_Computing.html#efi-cc-measurement-protocol [1]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[ardb: Drop code changes, keep typedefs and #define's only]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The LINUX_EFI_ GUID identifiers are only intended to be used to refer to
GUIDs that are part of the Linux implementation, and are not considered
external ABI. (Famous last words).
GUIDs that already have a symbolic name in the spec should use that
name, to avoid confusion between firmware components. So use the
official name EFI_TCG2_FINAL_EVENTS_TABLE_GUID for the TCG2 'final
events' configuration table.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Our efi_tcg2_tagged_event is not defined in the EFI spec, but it is not
a local invention either: it was taken from the TCG PC Client spec,
where it is called TCG_PCClientTaggedEvent.
Note that this spec also contains some guidance on how to populate it,
which is not being followed closely at the moment; it claims that the
event size should cover the TCG_PCClientTaggedEvent and its payload
only, but it currently covers the preceding efi_tcg2_event too.
However, this directly contradicts the TCG EFI protocol specification,
which states very clearly that the event size should cover the entire
data structure, including the leading efi_tcg2_event_t struct.
So rename the struct and document its provenance, but retain the
existing logic to populate the size field.
Link: https://lore.kernel.org/all/20240308085754.476197-8-ardb+git@google.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Both AER and DPC RP PIO provide TLP Header Log registers (PCIe r6.1 secs
7.8.4 & 7.9.14) to convey error diagnostics but the struct is named after
AER as the struct aer_header_log_regs. Also, not all places that handle TLP
Header Log use the struct and the struct members are named individually.
Generalize the struct name and members, and use it consistently where TLP
Header Log is being handled so that a pcie_read_tlp_log() helper can be
easily added.
Link: https://lore.kernel.org/r/20240206135717.8565-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: drop ixgbe changes for now, tidy whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Allow the callers to set fwnode link flags when adding fwnode links.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240305050458.1400667-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add zynqmp_pm_efuse_access API in the ZynqMP
firmware for read/write access of efuse memory.
Signed-off-by: Praveen Teja Kundanala <praveen.teja.kundanala@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240224114516.86365-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initialize debugfs_root to -ENODEV so that if the client never sets a
valid debugfs root the debugfs files will not be created.
A NULL pointer passed to any of the debugfs_create_*() functions means
"create in the root of debugfs". It doesn't mean "ignore".
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://msgid.link/r/20240307105353.40067-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V firmware drivers for v6.9
A single minor fix for an oversized allocation due to sizeof() misuse by
yours truly that came in since I sent my last fixes PR.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-firmware-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
firmware: microchip: Fix over-requested allocation size
Link: https://lore.kernel.org/r/20240305-vicinity-dumpling-8943ef26f004@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Arm SCMI spec. v3.2, s4.5.3.12 PERFORMANCE_DESCRIBE_FASTCHANNEL
defines a per-domain rate_limit for performance requests:
"""
Rate Limit in microseconds, indicating the minimum time
required between successive requests. A value of 0
indicates that this field is not applicable or supported
on the platform.
""""
The field is first defined in SCMI v2.0.
Add support to fetch this value and advertise it through
a fast_switch_rate_limit() callback.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Arm SCMI spec. v3.2, s4.5.3.4 PERFORMANCE_DOMAIN_ATTRIBUTES
defines a per-domain rate_limit for performance requests:
"""
Rate Limit in microseconds, indicating the minimum time
required between successive requests. A value of 0
indicates that this field is not supported by the
platform. This field does not apply to FastChannels.
""""
The field is first defined in SCMI v1.0.
Add support to fetch this value and advertise it through
a rate_limit_get() callback.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
cocci warnings: (new ones prefixed by >>)
>> drivers/firmware/microchip/mpfs-auto-update.c:387:72-78:
ERROR: application of sizeof to pointer
drivers/firmware/microchip/mpfs-auto-update.c:170:72-78:
ERROR: application of sizeof to pointer
response_msg is a pointer to u32, so the size of element it points to is
supposed to be a multiple of sizeof(u32), rather than sizeof(u32 *).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403040516.CYxoWTXw-lkp@intel.com/
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Fixes: ec5b0f1193ad ("firmware: microchip: add PolarFire SoC Auto Update support")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The early SME/SEV code parses the command line very early, in order to
decide whether or not memory encryption should be enabled, which needs
to occur even before the initial page tables are created.
This is problematic for a number of reasons:
- this early code runs from the 1:1 mapping provided by the decompressor
or firmware, which uses a different translation than the one assumed by
the linker, and so the code needs to be built in a special way;
- parsing external input while the entire kernel image is still mapped
writable is a bad idea in general, and really does not belong in
security minded code;
- the current code ignores the built-in command line entirely (although
this appears to be the case for the entire decompressor)
Given that the decompressor/EFI stub is an intrinsic part of the x86
bootable kernel image, move the command line parsing there and out of
the core kernel. This removes the need to build lib/cmdline.o in a
special way, or to use RIP-relative LEA instructions in inline asm
blocks.
This involves a new xloadflag in the setup header to indicate
that mem_encrypt=on appeared on the kernel command line.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240227151907.387873-17-ardb+git@google.com
|
|
Parse the mem_encrypt= command line parameter from the EFI stub if
CONFIG_ARCH_HAS_MEM_ENCRYPT=y, so that it can be passed to the early
boot code by the arch code in the stub.
This avoids the need for the core kernel to do any string parsing very
early in the boot.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240227151907.387873-16-ardb+git@google.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/drivers
firmware: tegra: Changes for v6.9-rc1
Contains a fix that makes sure we don't unnecessarily call kfree().
* tag 'tegra-for-6.9-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware: tegra: bpmp: Return directly after a failed kzalloc() in get_filename()
Link: https://lore.kernel.org/r/20240223174849.1509465-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/drivers
Arm SCMI updates for v6.9
Quite a few changes to extend support to SCMI v3.2 specification,
to enhance notification handling and other miscellaneous updates.
1. Enhancements to notification handling
Until now, trying to register a notifier for an unsuppported
notification returned an error genrating unneeded message exchanges
with the SCMI platform. This can be avoided by looking up in advance
the specific protocol and resources available.
With these changes SCMI driver user will fail to register a notifier
if the related command or resource is not supported (like before)
without the need of exchanging any message.
Perf notifications are also extended to provide the pre-calculated
frequencies corresponding to the level or index carried by the
2. More SCMI v3.2 related updates
One of the main addition includes a centralized support to the SCMI
core to handle v3.2 optional protocol version negotiation, so that
at protocol initialization time, if the platform advertised version
is newer than supported by the kernel and protocol version negotiation
is supported, the SCMI core will attempt to negotiate an older protocol
version.
It also includes the clock get permissions which indicates if any of
the clock operations are forbidden by the platform for the OSPM agent.
It can be used in the clock driver to avoid unnecessary message
exchanges between the kernel and the platform which will always end
up with the failure. It also includes other missing bits of clock
v3.2 protocol so that the supported protocol version can be bumped
to 0x30000 (v3.2).
3. Miscellaneous updates
This includes addition of warning if the domain frequency multiplier
is 0 or rounded off to indicate the actual frequencies are either
wrong ot rounded off, hardening of clock domain info lookups, addition
of multiple protocols registration support within a SCMI driver,
update to SCMI entry in MAINTAINERS to include HWMON driver and
constifying the scmi_bus_type structure.
This also includes couple for fixes to minor issues: double free in
SMC transport cleanup path and struct kernel-doc warnings in optee
transport.
* tag 'scmi-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: (29 commits)
MAINTAINERS: Update SCMI entry with HWMON driver
firmware: arm_scmi: Update the supported clock protocol version
firmware: arm_scmi: Add standard clock OEM definitions
firmware: arm_scmi: Add clock check for extended config support
firmware: arm_scmi: Add support for v3.2 NEGOTIATE_PROTOCOL_VERSION
firmware: arm_scmi: Fix struct kernel-doc warnings in optee transport
firmware: arm_scmi: Report frequencies in the perf notifications
firmware: arm_scmi: Use opps_by_lvl to store opps
firmware: arm_scmi: Implement is_notify_supported callback in powercap protocol
firmware: arm_scmi: Implement is_notify_supported callback in reset protocol
firmware: arm_scmi: Implement is_notify_supported callback in sensor protocol
firmware: arm_scmi: Implement is_notify_supported callback in clock protocol
firmware: arm_scmi: Implement is_notify_supported callback in system power protocol
firmware: arm_scmi: Implement is_notify_supported callback in power protocol
firmware: arm_scmi: Implement is_notify_supported callback in perf protocol
firmware: arm_scmi: Add a common helper to check if a message is supported
firmware: arm_scmi: Check for notification support
firmware: arm_scmi: Make scmi_bus_type const
firmware: arm_scmi: Fix double free in SMC transport cleanup path
firmware: arm_scmi: Implement clock get permissions
...
Link: https://lore.kernel.org/r/20240223033435.118028-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"Only the EFI variable name size change is significant, and will be
backported once it lands. The others are cleanup.
- Fix phys_addr_t size confusion in 32-bit capsule loader
- Reduce maximum EFI variable name size to 512 to work around buggy
firmware
- Drop some redundant code from efivarfs while at it"
* tag 'efi-fixes-for-v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efivarfs: Drop 'duplicates' bool parameter on efivar_init()
efivarfs: Drop redundant cleanup on fill_super() failure
efivarfs: Request at most 512 bytes for variable names
efi/capsule-loader: fix incorrect allocation size
|
|
This error path accidentally returns success when it should preserve the
error code from sysfb_parent_dev().
Fixes: 4e754597d603 ("firmware/sysfb: Create firmware device only for enabled PCI devices")
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/aaaa2e13-849b-41a0-8186-25f3d2a16f86@moroto.mountain
|
|
Thomas Zimmermann asked to backmerge -rc6 for drm-misc branches,
there's a few same-area-changed conflicts (xe and amdgpu mostly) that
are getting a bit too annoying.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now move the relevant codes into separate files:
kernel/crash_reserve.c, include/linux/crash_reserve.h.
And add config item CRASH_RESERVE to control its enabling.
And also update the old ifdeffery of CONFIG_CRASH_CORE, including of
<linux/crash_core.h> and config item dependency on CRASH_CORE
accordingly.
And also do renaming as follows:
- arch/xxx/kernel/{crash_core.c => vmcore_info.c}
because they are only related to vmcoreinfo exporting on x86, arm64,
riscv.
And also Remove config item CRASH_CORE, and rely on CONFIG_KEXEC_CORE to
decide if build in crash_core.c.
[yang.lee@linux.alibaba.com: remove duplicated include in vmcore_info.c]
Link: https://lkml.kernel.org/r/20240126005744.16561-1-yang.lee@linux.alibaba.com
Link: https://lkml.kernel.org/r/20240124051254.67105-3-bhe@redhat.com
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Hari Bathini <hbathini@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pingfan Liu <piliu@redhat.com>
Cc: Klara Modin <klarasmodin@gmail.com>
Cc: Michael Kelley <mhklinux@outlook.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
Microchip firmware driver fixes for v6.8-rc6
A single fix for me incorrectly using sizeof().
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-firmware-fixes-for-v6.8-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
firmware: microchip: fix wrong sizeof argument
Link: https://lore.kernel.org/r/20240221-recognize-dust-4bb575f4e67b@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
LLVM moved their issue tracker from their own Bugzilla instance to GitHub
issues. While all of the links are still valid, they may not necessarily
show the most up to date information around the issues, as all updates
will occur on GitHub, not Bugzilla.
Another complication is that the Bugzilla issue number is not always the
same as the GitHub issue number. Thankfully, LLVM maintains this mapping
through two shortlinks:
https://llvm.org/bz<num> -> https://bugs.llvm.org/show_bug.cgi?id=<num>
https://llvm.org/pr<num> -> https://github.com/llvm/llvm-project/issues/<mapped_num>
Switch all "https://bugs.llvm.org/show_bug.cgi?id=<num>" links to the
"https://llvm.org/pr<num>" shortlink so that the links show the most up to
date information. Each migrated issue links back to the Bugzilla entry,
so there should be no loss of fidelity of information here.
Link: https://lkml.kernel.org/r/20240109-update-llvm-links-v1-3-eb09b59db071@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Fangrui Song <maskray@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mykola Lysenko <mykolal@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The efi-pstore module parameter "pstore_disable" warrants that users
are able to deactivate such backend. There is also a Kconfig option
for the default value of this parameter. It was originally added due
to some bad UEFI FW implementations that could break with many variables
written.
Some distros (such as Arch Linux) set this in their config file still
nowadays. And once it is set, even being a writable module parameter,
there is effectively no way to make use of efi-pstore anymore.
If "pstore_disable" is set to true, the init function of the module exits
early and is never called again after the initcall processing.
Let's switch this module parameter to have a callback and perform the
pstore backend registration again each time it's set from Y->N (and
vice-versa). With this, the writable nature of the parameter starts to
make sense, given that users now can switch back to using efi-pstore
or not during runtime by writing into it.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20240103184053.226203-1-gpiccoli@igalia.com
Signed-off-by: Kees Cook <keescook@chromium.org>
|
Linus Torvalds
Oleksandr Tymoshenko
Ard Biesheuvel
KONDO KAZUMA(近藤 和真)
Samuel Thibault
Rafael J. Wysocki
Sibi Sankar
Ingo Molnar
Kuppuswamy Sathyanarayanan
Ilpo Järvinen
Saravana Kannan
Praveen Teja Kundanala
Richard Fitzgerald
Arnd Bergmann
Pierre Gondois
Dawei Li
Dan Carpenter
Daniel Vetter
Baoquan He
Nathan Chancellor
Guilherme G. Piccoli
