| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e4454 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
entry
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df88 ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab9f ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sja1105_dynamic_config_poll_valid()
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4d9423549501 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a new fdb entry is added (with both ports of the
ADIN2111 bridged), the driver configures the MAC filters for the wrong
port, which results in the forwarding being done by the host, and not
actually hardware offloaded.
The ADIN2111 offloads the forwarding by setting filters on the
destination MAC address of incoming frames. Based on these, they may be
routed to the other port. Thus, if a frame has to be forwarded from port
1 to port 2, the required configuration for the ADDR_FILT_UPRn register
should set the APPLY2PORT1 bit (instead of APPLY2PORT2, as it's
currently the case).
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mtk_hwlro_get_fdir_all()
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference.
Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rules is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rules to avoid OOB writing or NULL pointer dereference.
Fixes: 90b509b39ac9 ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid OOB writing or NULL pointer dereference.
Fixes: c5d511c49587 ("net: bcmasp: Add support for wake on net filters")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting ethtool -C eth0 tx-usecs 0 is supposed to disable the use of the
coalescing timer but currently it gets programmed with zero delay
instead.
Disable the use of the coalescing timer if tx-usecs is zero by
preventing it from being restarted. Note that to keep things simple we
don't start/stop the timer when the coalescing settings are changed, but
just let that happen on the next transmit or timer expiry.
Fixes: 8fce33317023 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The access to page pool `cache' array and the `count' variable
is not locked. Page pool cache access is fine as long as there
is only one consumer per pool.
octeontx2 driver fills in rx buffers from page pool in NAPI context.
If system is stressed and could not allocate buffers, refiiling work
will be delegated to a delayed workqueue. This means that there are
two cosumers to the page pool cache.
Either workqueue or IRQ/NAPI can be run on other CPU. This will lead
to lock less access, hence corruption of cache pool indexes.
To fix this issue, NAPI is rescheduled from workqueue context to refill
rx buffers.
Fixes: b2e3406a38f0 ("octeontx2-pf: Add support for page pool")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inject fault When select CONFIG_VCAP_KUNIT_TEST, the below memory leak
occurs. If kzalloc() for duprule succeeds, but the following
kmemdup() fails, the duprule, ckf and caf memory will be leaked. So kfree
them in the error path.
unreferenced object 0xffff122744c50600 (size 192):
comm "kunit_try_catch", pid 346, jiffies 4294896122 (age 911.812s)
hex dump (first 32 bytes):
10 27 00 00 04 00 00 00 1e 00 00 00 2c 01 00 00 .'..........,...
00 00 00 00 00 00 00 00 18 06 c5 44 27 12 ff ff ...........D'...
backtrace:
[<00000000394b0db8>] __kmem_cache_alloc_node+0x274/0x2f8
[<0000000001bedc67>] kmalloc_trace+0x38/0x88
[<00000000b0612f98>] vcap_dup_rule+0x50/0x460
[<000000005d2d3aca>] vcap_add_rule+0x8cc/0x1038
[<00000000eef9d0f8>] test_vcap_xn_rule_creator.constprop.0.isra.0+0x238/0x494
[<00000000cbda607b>] vcap_api_rule_remove_in_front_test+0x1ac/0x698
[<00000000c8766299>] kunit_try_run_case+0xe0/0x20c
[<00000000c4fe9186>] kunit_generic_run_threadfn_adapter+0x50/0x94
[<00000000f6864acf>] kthread+0x2e8/0x374
[<0000000022e639b3>] ret_from_fork+0x10/0x20
Fixes: 814e7693207f ("net: microchip: vcap api: Add a storage state to a VCAP rule")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_available_child_of_node performs an of_node_get
on each iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking updates from Jakub Kicinski:
"Including fixes from netfilter and bpf.
Current release - regressions:
- eth: stmmac: fix failure to probe without MAC interface specified
Current release - new code bugs:
- docs: netlink: fix missing classic_netlink doc reference
Previous releases - regressions:
- deal with integer overflows in kmalloc_reserve()
- use sk_forward_alloc_get() in sk_get_meminfo()
- bpf_sk_storage: fix the missing uncharge in sk_omem_alloc
- fib: avoid warn splat in flow dissector after packet mangling
- skb_segment: call zero copy functions before using skbuff frags
- eth: sfc: check for zero length in EF10 RX prefix
Previous releases - always broken:
- af_unix: fix msg_controllen test in scm_pidfd_recv() for
MSG_CMSG_COMPAT
- xsk: fix xsk_build_skb() dereferencing possible ERR_PTR()
- netfilter:
- nft_exthdr: fix non-linear header modification
- xt_u32, xt_sctp: validate user space input
- nftables: exthdr: fix 4-byte stack OOB write
- nfnetlink_osf: avoid OOB read
- one more fix for the garbage collection work from last release
- igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
- bpf, sockmap: fix preempt_rt splat when using raw_spin_lock_t
- handshake: fix null-deref in handshake_nl_done_doit()
- ip: ignore dst hint for multipath routes to ensure packets are
hashed across the nexthops
- phy: micrel:
- correct bit assignments for cable test errata
- disable EEE according to the KSZ9477 errata
Misc:
- docs/bpf: document compile-once-run-everywhere (CO-RE) relocations
- Revert "net: macsec: preserve ingress frame ordering", it appears
to have been developed against an older kernel, problem doesn't
exist upstream"
* tag 'net-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()
Revert "net: team: do not use dynamic lockdep key"
net: hns3: remove GSO partial feature bit
net: hns3: fix the port information display when sfp is absent
net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
net: hns3: fix debugfs concurrency issue between kfree buffer and read
net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
net: hns3: Support query tx timeout threshold by debugfs
net: hns3: fix tx timeout issue
net: phy: Provide Module 4 KSZ9477 errata (DS80000754C)
netfilter: nf_tables: Unbreak audit log reset
netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for ip_set_hash_netportnet.c
netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
netfilter: nf_tables: uapi: Describe NFTA_RULE_CHAIN_ID
netfilter: nfnetlink_osf: avoid OOB read
netfilter: nftables: exthdr: fix 4-byte stack OOB write
selftests/bpf: Check bpf_sk_storage has uncharged sk_omem_alloc
bpf: bpf_sk_storage: Fix the missing uncharge in sk_omem_alloc
bpf: bpf_sk_storage: Fix invalid wait context lockdep report
s390/bpf: Pass through tail call counter in trampolines
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various cleanups and fixes across the board"
* tag 'pwm/for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (31 commits)
pwm: lpc32xx: Remove handling of PWM channels
pwm: atmel: Simplify using devm functions
dt-bindings: pwm: brcm,kona-pwm: convert to YAML
pwm: stmpe: Handle errors when disabling the signal
pwm: stm32: Simplify using devm_pwmchip_add()
pwm: stm32: Don't modify HW state in .remove() callback
pwm: Fix order of freeing resources in pwmchip_remove()
pwm: ntxec: Use device_set_of_node_from_dev()
pwm: ntxec: Drop a write-only variable from driver data
pwm: pxa: Don't reimplement of_device_get_match_data()
pwm: lpc18xx-sct: Simplify using devm_clk_get_enabled()
pwm: atmel-tcb: Don't track polarity in driver data
pwm: atmel-tcb: Unroll atmel_tcb_pwm_set_polarity() into only caller
pwm: atmel-tcb: Put per-channel data into driver data
pwm: atmel-tcb: Fix resource freeing in error path and remove
pwm: atmel-tcb: Harmonize resource allocation order
pwm: Drop unused #include <linux/radix-tree.h>
pwm: rz-mtu3: Fix build warning 'num_channel_ios' not described
pwm: Remove outdated documentation for pwmchip_remove()
pwm: atmel: Enable clk when pwm already enabled in bootloader
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Add a way for drivers to tell the core the supported alarm range is
smaller than the date range. This is not used yet but will be
useful for the alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support"
* tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (73 commits)
dt-bindings: rtc: ds3231: Remove text binding
rtc: wm8350: remove unnecessary messages
rtc: twl: remove unnecessary messages
rtc: sun6i: remove unnecessary message
rtc: stop warning for invalid alarms when the alarm is disabled
rtc: twl: add NVRAM support
rtc: pcf85363: Allow to wake up system without IRQ
rtc: m48t86: add DT support for m48t86
dt-bindings: rtc: Add ST M48T86
rtc: pcf2127: remove useless check
rtc: rzn1: Report maximum alarm limit to rtc core
rtc: ds1305: Report maximum alarm limit to rtc core
rtc: tps6586x: Report maximum alarm limit to rtc core
rtc: cmos: Report supported alarm limit to rtc infrastructure
rtc: cros-ec: Detect and report supported alarm window size
rtc: Add support for limited alarm timer offsets
rtc: isl1208: Fix incorrect logic in isl1208_set_xtoscb()
MAINTAINERS: remove obsolete pattern in RTC SUBSYSTEM section
rtc: tps65910: Remove redundant dev_warn() and do not check for 0 return after calling platform_get_irq()
rtc: omap: Do not check for 0 return after calling platform_get_irq()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Core:
- Fix SETDASA when static and dynamic adress are equal
- Fix cmd_v1 DAA exit criteria
Drivers:
- svc: allow probing without any device"
* tag 'i3c/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: svc: fix probe failure when no i3c device exist
i3c: master: Fix SETDASA process
dt-bindings: i3c: Fix description for assigned-address
i3c: master: svc: Describe member 'saved_regs'
i3c: master: svc: Do not check for 0 return after calling platform_get_irq()
i3c/master: cmd_v1: Fix the exit criteria for the daa procedure
i3c: Explicitly include correct DT includes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes that came in during the merge window, both driver
specific - one for a bug that came up in testing, one for a bug due
to a misreading of the datasheet"
* tag 'regulator-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps6594-regulator: Fix random kernel crash
regulator: tps6287x: Fix n_voltages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of fixes for the sun6i driver. The patch to reduce DMA RX to
single byte width all the time is *hopefully* excessively cautious but
it's unclear which SoCs are affected so the fix just covers everything
for safety"
* tag 'spi-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
spi: sun6i: reduce DMA RX transfer width to single byte
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Clean up vCPU targets, always returning generic v8 as the preferred
target
- Trap forwarding infrastructure for nested virtualization (used for
traps that are taken from an L2 guest and are needed by the L1
hypervisor)
- FEAT_TLBIRANGE support to only invalidate specific ranges of
addresses when collapsing a table PTE to a block PTE. This avoids
that the guest refills the TLBs again for addresses that aren't
covered by the table PTE.
- Fix vPMU issues related to handling of PMUver.
- Don't unnecessary align non-stack allocations in the EL2 VA space
- Drop HCR_VIRT_EXCP_MASK, which was never used...
- Don't use smp_processor_id() in kvm_arch_vcpu_load(), but the cpu
parameter instead
- Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
- Remove prototypes without implementations
RISC-V:
- Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
- Added ONE_REG interface for SATP mode
- Added ONE_REG interface to enable/disable multiple ISA extensions
- Improved error codes returned by ONE_REG interfaces
- Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
- Added get-reg-list selftest for KVM RISC-V
s390:
- PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch)
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
- Guest debug fixes (Ilya)
x86:
- Clean up KVM's handling of Intel architectural events
- Intel bugfixes
- Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use
debug registers and generate/handle #DBs
- Clean up LBR virtualization code
- Fix a bug where KVM fails to set the target pCPU during an IRTE
update
- Fix fatal bugs in SEV-ES intrahost migration
- Fix a bug where the recent (architecturally correct) change to
reinject #BP and skip INT3 broke SEV guests (can't decode INT3 to
skip it)
- Retry APIC map recalculation if a vCPU is added/enabled
- Overhaul emergency reboot code to bring SVM up to par with VMX, tie
the "emergency disabling" behavior to KVM actually being loaded,
and move all of the logic within KVM
- Fix user triggerable WARNs in SVM where KVM incorrectly assumes the
TSC ratio MSR cannot diverge from the default when TSC scaling is
disabled up related code
- Add a framework to allow "caching" feature flags so that KVM can
check if the guest can use a feature without needing to search
guest CPUID
- Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
- Fix KVM's handling of !visible guest roots to avoid premature
triple fault injection
- Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the
API surface that is needed by external users (currently only
KVMGT), and fix a variety of issues in the process
Generic:
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier
events to pass action specific data without needing to constantly
update the main handlers.
- Drop unused function declarations
Selftests:
- Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
- Add support for printf() in guest code and covert all guest asserts
to use printf-based reporting
- Clean up the PMU event filter test and add new testcases
- Include x86 selftests in the KVM x86 MAINTAINERS entry"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (279 commits)
KVM: x86/mmu: Include mmu.h in spte.h
KVM: x86/mmu: Use dummy root, backed by zero page, for !visible guest roots
KVM: x86/mmu: Disallow guest from using !visible slots for page tables
KVM: x86/mmu: Harden TDP MMU iteration against root w/o shadow page
KVM: x86/mmu: Harden new PGD against roots without shadow pages
KVM: x86/mmu: Add helper to convert root hpa to shadow page
drm/i915/gvt: Drop final dependencies on KVM internal details
KVM: x86/mmu: Handle KVM bookkeeping in page-track APIs, not callers
KVM: x86/mmu: Drop @slot param from exported/external page-track APIs
KVM: x86/mmu: Bug the VM if write-tracking is used but not enabled
KVM: x86/mmu: Assert that correct locks are held for page write-tracking
KVM: x86/mmu: Rename page-track APIs to reflect the new reality
KVM: x86/mmu: Drop infrastructure for multiple page-track modes
KVM: x86/mmu: Use page-track notifiers iff there are external users
KVM: x86/mmu: Move KVM-only page-track declarations to internal header
KVM: x86: Remove the unused page-track hook track_flush_slot()
drm/i915/gvt: switch from ->track_flush_slot() to ->track_remove_region()
KVM: x86: Add a new page-track hook to handle memslot deletion
drm/i915/gvt: Don't bother removing write-protection on to-be-deleted slot
KVM: x86: Reject memslot MOVE operations if KVMGT is attached
...
|
|
enetc_psi_create() returns an ERR_PTR() or a valid station interface
pointer, but checking for the non-NULL quality of the return code blurs
that difference away. So if enetc_psi_create() fails, we call
enetc_psi_destroy() when we shouldn't. This will likely result in
crashes, since enetc_psi_create() cleans up everything after itself when
it returns an ERR_PTR().
Fixes: f0168042a212 ("net: enetc: reimplement RFS/RSS memory clearing as PCI quirk")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/netdev/582183ef-e03b-402b-8e2d-6d9bb3c83bd9@moroto.mountain/
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230906141609.247579-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 39285e124edbc752331e98ace37cc141a6a3747a.
Looks like the change has unintended consequences in exposing
objects before they are initialized. Let's drop this patch
and try again in net-next.
Reported-by: syzbot+44ae022028805f4600fc@syzkaller.appspotmail.com
Fixes: 39285e124edb ("net: team: do not use dynamic lockdep key")
Link: https://lore.kernel.org/all/20230907103124.6adb7256@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- A couple of virtual vs physical address confusion fixes
- Rework locking in dcssblk driver to address a lockdep warning
- Remove support for "noexec" kernel command line option since there is
no use case where it would make sense
- Simplify kernel mapping setup and get rid of quite a bit of code
- Add architecture specific __set_memory_yy() functions which allow us
to modify kernel mappings. Unlike the set_memory_xx() variants they
take void pointer start and end parameters, which allows using them
without the usual casts, and also to use them on areas larger than
8TB.
Note that the set_memory_xx() family comes with an int num_pages
parameter which overflows with 8TB. This could be addressed by
changing the num_pages parameter to unsigned long, however requires
to change all architectures, since the module code expects an int
parameter (see module_set_memory()).
This was indeed an issue since for debug_pagealloc() we call
set_memory_4k() on the whole identity mapping. Therefore address this
for now with the __set_memory_yy() variant, and address common code
later
- Use dev_set_name() and also fix memory leak in zcrypt driver error
handling
- Remove unused lsi_mask from airq_struct
- Add warning for invalid kernel mapping requests
* tag 's390-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vmem: do not silently ignore mapping limit
s390/zcrypt: utilize dev_set_name() ability to use a formatted string
s390/zcrypt: don't leak memory if dev_set_name() fails
s390/mm: fix MAX_DMA_ADDRESS physical vs virtual confusion
s390/airq: remove lsi_mask from airq_struct
s390/mm: use __set_memory() variants where useful
s390/set_memory: add __set_memory() variant
s390/set_memory: generate all set_memory() functions
s390/mm: improve description of mapping permissions of prefix pages
s390/amode31: change type of __samode31, __eamode31, etc
s390/mm: simplify kernel mapping setup
s390: remove "noexec" option
s390/vmem: fix virtual vs physical address confusion
s390/dcssblk: fix lockdep warning
s390/monreader: fix virtual vs physical address confusion
|
|
Pull MIPS updates from Thomas Bogendoerfer:
"Just cleanups and fixes"
* tag 'mips_6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: TXx9: Do PCI error checks on own line
arch/mips/configs/*_defconfig cleanup
MIPS: VDSO: Conditionally export __vdso_gettimeofday()
Mips: loongson3_defconfig: Enable ast drm driver by default
mips: remove <asm/export.h>
mips: replace #include <asm/export.h> with #include <linux/export.h>
mips: remove unneeded #include <asm/export.h>
MIPS: Loongson64: Fix more __iomem attributes
MIPS: loongson32: Remove regs-rtc.h
MIPS: loongson32: Remove regs-clk.h
MIPS: More explicit DT include clean-ups
MIPS: Fixup explicit DT include clean-up
Revert MIPS: Loongson: Fix build error when make modules_install
MIPS: Only fiddle with CHECKFLAGS if `need-compiler'
MIPS: Fix CONFIG_CPU_DADDI_WORKAROUNDS `modules_install' regression
MIPS: Explicitly include correct DT includes
|
|
HNS3 NIC does not support GSO partial packets segmentation. Actually tunnel
packets for example NvGRE packets segment offload and checksum offload is
already supported. There is no need to keep gso partial feature bit. So
this patch removes it.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When sfp is absent or unidentified, the port type should be
displayed as PORT_OTHERS, rather than PORT_FIBRE.
Fixes: 88d10bd6f730 ("net: hns3: add support for multiple media type")
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We hope that tc qdisc and dcb ets commands can not be used crosswise.
If we want to use any of the commands to configure tc,
We must use the other command to clear the existing configuration.
However, when we configure a single tc with tc qdisc,
we can still configure it with dcb ets.
Because we use mqprio_active as the tag of tc qdisc configuration,
but with dcb ets, we do not check mqprio_active.
This patch fix this issue by check mqprio_active before
executing the dcb ets command. and add dcb_ets_active to
replace HCLGE_FLAG_DCB_ENABLE and HCLGE_FLAG_MQPRIO_ENABLE
at the hclge layer,
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Now in hns3_dbg_uninit(), there may be concurrency between
kfree buffer and read, it may result in memory error.
Moving debugfs_remove_recursive() in front of kfree buffer to ensure
they don't happen at the same time.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
req1->tcam_data is defined as "u8 tcam_data[8]", and we convert it as
(u32 *) without considerring byte order conversion,
it may result in printing wrong data for tcam_data.
Convert tcam_data to (__le32 *) first to fix it.
Fixes: b5a0b70d77b9 ("net: hns3: refactor dump fd tcam of debugfs")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
support query tx timeout threshold by debugfs
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the driver knocks the ring doorbell before updating
the ring->last_to_use in tx flow. if the hardware transmiting
packet and napi poll scheduling are fast enough, it may get
the old ring->last_to_use in drivers' napi poll.
In this case, the driver will think the tx is not completed, and
return directly without clear the flag __QUEUE_STATE_STACK_XOFF,
which may cause tx timeout.
Fixes: 20d06ca2679c ("net: hns3: optimize the tx clean process")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca045 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull ceph updates from Ilya Dryomov:
"Mixed with some fixes and cleanups, this brings in reasonably complete
fscrypt support to CephFS! The list of things which don't work with
encryption should be fairly short, mostly around the edges: fallocate
(not supported well in CephFS to begin with), copy_file_range
(requires re-encryption), non-default striping patterns.
This was a multi-year effort principally by Jeff Layton with
assistance from Xiubo Li, Luís Henriques and others, including several
dependant changes in the MDS, netfs helper library and fscrypt
framework itself"
* tag 'ceph-for-6.6-rc1' of https://github.com/ceph/ceph-client: (53 commits)
ceph: make num_fwd and num_retry to __u32
ceph: make members in struct ceph_mds_request_args_ext a union
rbd: use list_for_each_entry() helper
libceph: do not include crypto/algapi.h
ceph: switch ceph_lookup/atomic_open() to use new fscrypt helper
ceph: fix updating i_truncate_pagecache_size for fscrypt
ceph: wait for OSD requests' callbacks to finish when unmounting
ceph: drop messages from MDS when unmounting
ceph: update documentation regarding snapshot naming limitations
ceph: prevent snapshot creation in encrypted locked directories
ceph: add support for encrypted snapshot names
ceph: invalidate pages when doing direct/sync writes
ceph: plumb in decryption during reads
ceph: add encryption support to writepage and writepages
ceph: add read/modify/write to ceph_sync_write
ceph: align data in pages in ceph_sync_write
ceph: don't use special DIO path for encrypted inodes
ceph: add truncate size handling support for fscrypt
ceph: add object version support for sync read
libceph: allow ceph_osdc_new_request to accept a multi-op read
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for Azoteq IQS7210A/7211A/E touch controllers
- support for Azoteq IQS7222D variant added to iqs7222 driver
- support for touch keys functionality added to Melfas MMS114 driver
- new hardware IDs added to exc3000 and Goodix drivers
- xpad driver gained support for GameSir T4 Kaleid Controller
- a fix for xpad driver to properly support some third-party
controllers that need a magic packet to start properly
- a fix for psmouse driver to more reliably switch to RMI4 mode on
devices that use native RMI4/SMbus protocol
- a quirk for i8042 for TUXEDO Gemini 17 Gen1/Clevo PD70PN laptops
- multiple drivers have been updated to make use of devm and other
newer APIs such as dev_err_probe(), devm_regulator_get_enable(), and
others.
* tag 'input-for-v6.6-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (83 commits)
Input: goodix - add support for ACPI ID GDX9110
Input: rpckbd - fix the return value handle for platform_get_irq()
Input: tca6416-keypad - switch to using input core's polling features
Input: tca6416-keypad - convert to use devm_* api
Input: tca6416-keypad - fix interrupt enable disbalance
Input: tca6416-keypad - rely on I2C core to set up suspend/resume
Input: tca6416-keypad - always expect proper IRQ number in i2c client
Input: lm8323 - convert to use devm_* api
Input: lm8323 - rely on device core to create kp_disable attribute
Input: qt2160 - convert to use devm_* api
Input: qt2160 - do not hard code interrupt trigger
Input: qt2160 - switch to using threaded interrupt handler
Input: qt2160 - tweak check for i2c adapter functionality
Input: psmouse - add delay when deactivating for SMBus mode
Input: mcs-touchkey - fix uninitialized use of error in mcs_touchkey_probe()
Input: qt1070 - convert to use devm_* api
Input: mcs-touchkey - convert to use devm_* api
Input: amikbd - convert to use devm_* api
Input: lm8333 - convert to use devm_* api
Input: mms114 - add support for touch keys
...
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add marvell GTI watchdog driver
- add support for Amlogic-T7 SoCs
- document the IPQ5018 watchdog compatible
- enable COMPILE_TEST for more watchdog device drivers
- core: stop watchdog when executing poweroff command
- other small improvements and fixes
* tag 'linux-watchdog-6.6-rc1' of git://www.linux-watchdog.org/linux-watchdog: (21 commits)
watchdog: Add support for Amlogic-T7 SoCs
watchdog: Add a new struct for Amlogic-GXBB driver
dt-bindings: watchdog: Add support for Amlogic-T7 SoCs
dt-bindings: watchdog: qcom-wdt: document IPQ5018
watchdog: imx2_wdt: Improve dev_crit() message
watchdog: stm32: Drop unnecessary of_match_ptr()
watchdog: sama5d4: readout initial state
watchdog: intel-mid_wdt: add MODULE_ALIAS() to allow auto-load
watchdog: core: stop watchdog when executing poweroff command
watchdog: pm8916_wdt: Remove redundant of_match_ptr()
watchdog: xilinx_wwdt: Use div_u64() in xilinx_wwdt_start()
watchdog: starfive: Remove #ifdef guards for PM related functions
watchdog: s3c2410: Fix potential deadlock on &wdt->lock
watchdog:rit_wdt: Add support for WDIOF_CARDRESET
dt-bindings: watchdog: ti,rti-wdt: Add support for WDIOF_CARDRESET
watchdog: Enable COMPILE_TEST for more drivers
watchdog: advantech_ec_wdt: fix Kconfig dependencies
watchdog: Explicitly include correct DT includes
Watchdog: Add marvell GTI watchdog driver
dt-bindings: watchdog: marvell GTI system watchdog driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Functionality:
- Ensure correct includes are present and remove some that are not
required
- Drop redundant of_match_ptr() call to cast pointer to NULL
Bug Fixes:
- Revert to old (expected) behaviour of initialising PWM state on
first brightness change
- Correctly handle / propagate errors
- Fix 'sometimes-uninitialised' issues"
* tag 'backlight-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: led_bl: Remove redundant of_match_ptr()
backlight: lp855x: Drop ret variable in brightness change function
backlight: gpio_backlight: Drop output GPIO direction check for initial power state
backlight: lp855x: Catch errors when changing brightness
backlight: lp855x: Initialize PWM state on first brightness change
backlight: qcom-wled: Explicitly include correct DT includes
|
|
The blamed commit left this delta behind:
struct sja1105_cbs_entry {
- u64 port;
- u64 prio;
+ u64 port; /* Not used for SJA1110 */
+ u64 prio; /* Not used for SJA1110 */
u64 credit_hi;
u64 credit_lo;
u64 send_slope;
u64 idle_slope;
};
but did not actually implement tc-cbs offload fully for the new switch.
The offload is accepted, but it doesn't work.
The difference compared to earlier switch generations is that now, the
table of CBS shapers is sparse, because there are many more shapers, so
the mapping between a {port, prio} and a table index is static, rather
than requiring us to store the port and prio into the sja1105_cbs_entry.
So, the problem is that the code programs the CBS shaper parameters at a
dynamic table index which is incorrect.
All that needs to be done for SJA1110 CBS shapers to work is to bypass
the logic which allocates shapers in a dense manner, as for SJA1105, and
use the fixed mapping instead.
Fixes: 3e77e59bf8cf ("net: dsa: sja1105: add support for the SJA1110 switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After running command [2] too many times in a row:
[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
idleslope 120000 sendslope -880000 locredit -1320 hicredit 180
(aka more than priv->info->num_cbs_shapers times)
we start seeing the following error message:
Error: Specified device failed to setup cbs hardware offload.
This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.
Fixes: 4d7525085a9b ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
More careful measurement of the tc-cbs bandwidth shows that the stream
bandwidth (effectively idleslope) increases, there is a larger and
larger discrepancy between the rate limit obtained by the software
Qdisc, and the rate limit obtained by its offloaded counterpart.
The discrepancy becomes so large, that e.g. at an idleslope of 40000
(40Mbps), the offloaded cbs does not actually rate limit anything, and
traffic will pass at line rate through a 100 Mbps port.
The reason for the discrepancy is that the hardware documentation I've
been following is incorrect. UM11040.pdf (for SJA1105P/Q/R/S) states
about IDLE_SLOPE that it is "the rate (in unit of bytes/sec) at which
the credit counter is increased".
Cross-checking with UM10944.pdf (for SJA1105E/T) and UM11107.pdf
(for SJA1110), the wording is different: "This field specifies the
value, in bytes per second times link speed, by which the credit counter
is increased".
So there's an extra scaling for link speed that the driver is currently
not accounting for, and apparently (empirically), that link speed is
expressed in Kbps.
I've pondered whether to pollute the sja1105_mac_link_up()
implementation with CBS shaper reprogramming, but I don't think it is
worth it. IMO, the UAPI exposed by tc-cbs requires user space to
recalculate the sendslope anyway, since the formula for that depends on
port_transmit_rate (see man tc-cbs), which is not an invariant from tc's
perspective.
So we use the offload->sendslope and offload->idleslope to deduce the
original port_transmit_rate from the CBS formula, and use that value to
scale the offload->sendslope and offload->idleslope to values that the
hardware understands.
Some numerical data points:
40Mbps stream, max interfering frame size 1500, port speed 100M
---------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -60000 locredit -900 hicredit 600
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 600 600
credit_lo 900 900
send_slope 7500000 75
idle_slope 5000000 50
40Mbps stream, max interfering frame size 1500, port speed 1G
-------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -960000 locredit -1440 hicredit 60
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 60 60
credit_lo 1440 1440
send_slope 120000000 120
idle_slope 5000000 5
5.12Mbps stream, max interfering frame size 1522, port speed 100M
-----------------------------------------------------------------
tc-cbs parameters:
idleslope 5120 sendslope -94880 locredit -1444 hicredit 77
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 77 77
credit_lo 1444 1444
send_slope 11860000 118
idle_slope 640000 6
Tested on SJA1105T, SJA1105S and SJA1110A, at 1Gbps and 100Mbps.
Fixes: 4d7525085a9b ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Change MIN_TXD and MIN_RXD to allow set rx/tx value between 64 and 80
Olga Zaborska says:
Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igb, igbvf and igc devices can use as low as 64
descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ACL flow table is required in switchdev mode when metadata is enabled,
driver creates such table when loading each vport. However, not every
vport is loaded in switchdev mode. Such as ECPF if it's the eswitch manager.
In this case, ACL flow table is still needed.
To make it modularized, create ACL flow table for eswitch manager as
default and skip such operations when loading manager vport.
Also, there is no need to load the eswitch manager vport in switchdev mode.
This means there is no need to load it on regular connect-x HCAs where
the PF is the eswitch manager. This will avoid creating duplicate ACL
flow table for host PF vport.
Fixes: 29bcb6e4fe70 ("net/mlx5e: E-Switch, Use metadata for vport matching in send-to-vport rules")
Fixes: eb8e9fae0a22 ("mlx5/core: E-Switch, Allocate ECPF vport if it's an eswitch manager")
Fixes: 5019833d661f ("net/mlx5: E-switch, Introduce helper function to enable/disable vports")
Signed-off-by: Bodong Wang <bodong@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the cited commit, the mirred devices are recorded and checked while
parsing the actions. In order to avoid system crash, the duplicate
action in a single rule is not allowed.
But the rule is actually break down into several FTEs in different
tables, for either mirroring, or the specified types of actions which
use post action infrastructure.
It will reject certain action list by mistake, for example:
actions:enp8s0f0_1,set(ipv4(ttl=63)),enp8s0f0_0,enp8s0f0_1.
Here the rule is split to two FTEs because of pedit action.
To fix this issue, when parsing the rule actions, reset if_count to
clear the mirred devices array if the rule is split to multiple
FTEs, and then the duplicate checking is restarted.
Fixes: 554fe75c1b3f ("net/mlx5e: Avoid duplicating rule destinations")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
team interface has used a dynamic lockdep key to avoid false-positive
lockdep deadlock detection. Virtual interfaces such as team usually
have their own lock for protecting private data.
These interfaces can be nested.
team0
|
team1
Each interface's lock is actually different(team0->lock and team1->lock).
So,
mutex_lock(&team0->lock);
mutex_lock(&team1->lock);
mutex_unlock(&team1->lock);
mutex_unlock(&team0->lock);
The above case is absolutely safe. But lockdep warns about deadlock.
Because the lockdep understands these two locks are same. This is a
false-positive lockdep warning.
So, in order to avoid this problem, the team interfaces started to use
dynamic lockdep key. The false-positive problem was fixed, but it
introduced a new problem.
When the new team virtual interface is created, it registers a dynamic
lockdep key(creates dynamic lockdep key) and uses it. But there is the
limitation of the number of lockdep keys.
So, If so many team interfaces are created, it consumes all lockdep keys.
Then, the lockdep stops to work and warns about it.
In order to fix this problem, team interfaces use the subclass instead
of the dynamic key. So, when a new team interface is created, it doesn't
register(create) a new lockdep, but uses existed subclass key instead.
It is already used by the bonding interface for a similar case.
As the bonding interface does, the subclass variable is the same as
the 'dev->nested_level'. This variable indicates the depth in the stacked
interface graph.
The 'dev->nested_level' is protected by RTNL and RCU.
So, 'mutex_lock_nested()' for 'team->lock' requires RTNL or RCU.
In the current code, 'team->lock' is usually acquired under RTNL, there is
no problem with using 'dev->nested_level'.
The 'team_nl_team_get()' and The 'lb_stats_refresh()' functions acquire
'team->lock' without RTNL.
But these don't iterate their own ports nested so they don't need nested
lock.
Reproducer:
for i in {0..1000}
do
ip link add team$i type team
ip link add dummy$i master team$i type dummy
ip link set dummy$i up
ip link set team$i up
done
Splat looks like:
BUG: MAX_LOCKDEP_ENTRIES too low!
turning off the locking correctness validator.
Please attach the output of /proc/lock_stat to the bug report
CPU: 0 PID: 4104 Comm: ip Not tainted 6.5.0-rc7+ #45
Call Trace:
<TASK>
dump_stack_lvl+0x64/0xb0
add_lock_to_list+0x30d/0x5e0
check_prev_add+0x73a/0x23a0
...
sock_def_readable+0xfe/0x4f0
netlink_broadcast+0x76b/0xac0
nlmsg_notify+0x69/0x1d0
dev_open+0xed/0x130
...
Reported-by: syzbot+9bbbacfbf1e04d5221f7@syzkaller.appspotmail.com
Fixes: 369f61bee0f5 ("team: fix nested locking lockdep warning")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RTC core already prints a message when the RTC is registered and when
registering fails, it is not necessary to have more in the driver.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230827221643.544259-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The RTC core already prints a message when the RTC is registered and when
registering fails, it is not necessary to have more in the driver.
Link: https://lore.kernel.org/r/20230827221643.544259-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The core already print a message once the rtc is successfully registered,
it is not necessary to print an other one.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230827221643.544259-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
When the alarm is not enabled, it may never have been set and so we can't
expect it to be valid. This will prevent the apparition of boot messages
like this one:
rtc rtc0: invalid alarm value: 2023-7-8 45:85:85
Link: https://lore.kernel.org/r/20230827221532.543353-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I3C masters are expected to support hot-join. This means at initialization
time we might not yet discover any device and this should not be treated
as a fatal error.
During the DAA procedure which happens at probe time, if no device has
joined, all CCC will be NACKed (from a bus perspective). This leads to an
early return with an error code which fails the probe of the master.
Let's avoid this by just telling the core through an I3C_ERROR_M2
return command code that no device was discovered, which is a valid
situation. This way the master will no longer bail out and fail to probe
for a wrong reason.
Cc: stable@vger.kernel.org
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230831141324.2841525-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Random kernel crash detected in TI CICD when regulator driver is added.
This is root caused to irq index increment being done twice causing
irq_data being allocated outside of the range.
- Rework tps6594_request_reg_irqs with correct index increment
- Adjust irq_data kmalloc size to the exact size needed for the device
This has been reported on TI mainline. No public bug report associated.
Reported-by: Udit Kumar <u-kumar1@ti.com>
Fixes: f17ccc5deb4d ("regulator: tps6594-regulator: Add driver for TI TPS6594 regulators")
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20230828-tps6594_random_boot_crash_fix-v1-1-f29cbf9ddb37@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
Hayes Wang
Vladimir Oltean
Ciprian Regus
Hangyu Hua
Vincent Whitchurch
Ratheesh Kannoth
Jinjie Ruan
Julia Lawall
Linus Torvalds
Jakub Kicinski
Jie Wang
Yisen Zhuang
Jijie Shao
Hao Chen
Jian Shen
Lukasz Majewski
David S. Miller
Bodong Wang
Jianbo Liu
Taehee Yoo
Alexandre Belloni
Frank Li
Jerome Neanne
