From 6dbdd4de0362c37e54e8b049781402e5a409e7d0 Mon Sep 17 00:00:00 2001 From: Vitaly Lifshits Date: Thu, 4 Jan 2024 16:16:52 +0200 Subject: e1000e: Workaround for sporadic MDI error on Meteor Lake systems On some Meteor Lake systems accessing the PHY via the MDIO interface may result in an MDI error. This issue happens sporadically and in most cases a second access to the PHY via the MDIO interface results in success. As a workaround, introduce a retry counter which is set to 3 on Meteor Lake systems. The driver will only return an error if 3 consecutive PHY access attempts fail. The retry mechanism is disabled in specific flows, where MDI errors are expected. Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake") Suggested-by: Nikolay Mushayev Co-developed-by: Nir Efrati Signed-off-by: Nir Efrati Signed-off-by: Vitaly Lifshits Tested-by: Naama Meir Signed-off-by: Tony Nguyen --- drivers/net/ethernet/intel/e1000e/hw.h | 2 + drivers/net/ethernet/intel/e1000e/ich8lan.c | 33 +++++ drivers/net/ethernet/intel/e1000e/phy.c | 182 +++++++++++++++++----------- drivers/net/ethernet/intel/e1000e/phy.h | 2 + 4 files changed, 150 insertions(+), 69 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h index 1fef6bb5a5fb..4b6e7536170a 100644 --- a/drivers/net/ethernet/intel/e1000e/hw.h +++ b/drivers/net/ethernet/intel/e1000e/hw.h @@ -628,6 +628,7 @@ struct e1000_phy_info { u32 id; u32 reset_delay_us; /* in usec */ u32 revision; + u32 retry_count; enum e1000_media_type media_type; @@ -644,6 +645,7 @@ struct e1000_phy_info { bool polarity_correction; bool speed_downgraded; bool autoneg_wait_to_complete; + bool retry_enabled; }; struct e1000_nvm_info { diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c index 19e450a5bd31..d8e97669f31b 100644 --- a/drivers/net/ethernet/intel/e1000e/ich8lan.c +++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c @@ -222,11 +222,18 @@ out: if (hw->mac.type >= e1000_pch_lpt) { /* Only unforce SMBus if ME is not active */ if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) { + /* Switching PHY interface always returns MDI error + * so disable retry mechanism to avoid wasting time + */ + e1000e_disable_phy_retry(hw); + /* Unforce SMBus mode in PHY */ e1e_rphy_locked(hw, CV_SMB_CTRL, &phy_reg); phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS; e1e_wphy_locked(hw, CV_SMB_CTRL, phy_reg); + e1000e_enable_phy_retry(hw); + /* Unforce SMBus mode in MAC */ mac_reg = er32(CTRL_EXT); mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; @@ -310,6 +317,11 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw) goto out; } + /* There is no guarantee that the PHY is accessible at this time + * so disable retry mechanism to avoid wasting time + */ + e1000e_disable_phy_retry(hw); + /* The MAC-PHY interconnect may be in SMBus mode. If the PHY is * inaccessible and resetting the PHY is not blocked, toggle the * LANPHYPC Value bit to force the interconnect to PCIe mode. @@ -380,6 +392,8 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw) break; } + e1000e_enable_phy_retry(hw); + hw->phy.ops.release(hw); if (!ret_val) { @@ -449,6 +463,11 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw) phy->id = e1000_phy_unknown; + if (hw->mac.type == e1000_pch_mtp) { + phy->retry_count = 2; + e1000e_enable_phy_retry(hw); + } + ret_val = e1000_init_phy_workarounds_pchlan(hw); if (ret_val) return ret_val; @@ -1146,6 +1165,11 @@ s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx) if (ret_val) goto out; + /* Switching PHY interface always returns MDI error + * so disable retry mechanism to avoid wasting time + */ + e1000e_disable_phy_retry(hw); + /* Force SMBus mode in PHY */ ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg); if (ret_val) @@ -1153,6 +1177,8 @@ s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx) phy_reg |= CV_SMB_CTRL_FORCE_SMBUS; e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg); + e1000e_enable_phy_retry(hw); + /* Force SMBus mode in MAC */ mac_reg = er32(CTRL_EXT); mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; @@ -1313,6 +1339,11 @@ static s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force) /* Toggle LANPHYPC Value bit */ e1000_toggle_lanphypc_pch_lpt(hw); + /* Switching PHY interface always returns MDI error + * so disable retry mechanism to avoid wasting time + */ + e1000e_disable_phy_retry(hw); + /* Unforce SMBus mode in PHY */ ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg); if (ret_val) { @@ -1333,6 +1364,8 @@ static s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force) phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS; e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg); + e1000e_enable_phy_retry(hw); + /* Unforce SMBus mode in MAC */ mac_reg = er32(CTRL_EXT); mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c index 5e329156d1ba..93544f1cc2a5 100644 --- a/drivers/net/ethernet/intel/e1000e/phy.c +++ b/drivers/net/ethernet/intel/e1000e/phy.c @@ -107,6 +107,16 @@ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw) return e1e_wphy(hw, M88E1000_PHY_GEN_CONTROL, 0); } +void e1000e_disable_phy_retry(struct e1000_hw *hw) +{ + hw->phy.retry_enabled = false; +} + +void e1000e_enable_phy_retry(struct e1000_hw *hw) +{ + hw->phy.retry_enabled = true; +} + /** * e1000e_read_phy_reg_mdic - Read MDI control register * @hw: pointer to the HW structure @@ -118,55 +128,73 @@ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw) **/ s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data) { + u32 i, mdic = 0, retry_counter, retry_max; struct e1000_phy_info *phy = &hw->phy; - u32 i, mdic = 0; + bool success; if (offset > MAX_PHY_REG_ADDRESS) { e_dbg("PHY Address %d is out of range\n", offset); return -E1000_ERR_PARAM; } + retry_max = phy->retry_enabled ? phy->retry_count : 0; + /* Set up Op-code, Phy Address, and register offset in the MDI * Control register. The MAC will take care of interfacing with the * PHY to retrieve the desired data. */ - mdic = ((offset << E1000_MDIC_REG_SHIFT) | - (phy->addr << E1000_MDIC_PHY_SHIFT) | - (E1000_MDIC_OP_READ)); + for (retry_counter = 0; retry_counter <= retry_max; retry_counter++) { + success = true; - ew32(MDIC, mdic); + mdic = ((offset << E1000_MDIC_REG_SHIFT) | + (phy->addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_READ)); - /* Poll the ready bit to see if the MDI read completed - * Increasing the time out as testing showed failures with - * the lower time out - */ - for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { - udelay(50); - mdic = er32(MDIC); - if (mdic & E1000_MDIC_READY) - break; - } - if (!(mdic & E1000_MDIC_READY)) { - e_dbg("MDI Read PHY Reg Address %d did not complete\n", offset); - return -E1000_ERR_PHY; - } - if (mdic & E1000_MDIC_ERROR) { - e_dbg("MDI Read PHY Reg Address %d Error\n", offset); - return -E1000_ERR_PHY; - } - if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) { - e_dbg("MDI Read offset error - requested %d, returned %d\n", - offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic)); - return -E1000_ERR_PHY; + ew32(MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { + usleep_range(50, 60); + mdic = er32(MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + e_dbg("MDI Read PHY Reg Address %d did not complete\n", + offset); + success = false; + } + if (mdic & E1000_MDIC_ERROR) { + e_dbg("MDI Read PHY Reg Address %d Error\n", offset); + success = false; + } + if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) { + e_dbg("MDI Read offset error - requested %d, returned %d\n", + offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic)); + success = false; + } + + /* Allow some time after each MDIC transaction to avoid + * reading duplicate data in the next MDIC transaction. + */ + if (hw->mac.type == e1000_pch2lan) + usleep_range(100, 150); + + if (success) { + *data = (u16)mdic; + return 0; + } + + if (retry_counter != retry_max) { + e_dbg("Perform retry on PHY transaction...\n"); + mdelay(10); + } } - *data = (u16)mdic; - /* Allow some time after each MDIC transaction to avoid - * reading duplicate data in the next MDIC transaction. - */ - if (hw->mac.type == e1000_pch2lan) - udelay(100); - return 0; + return -E1000_ERR_PHY; } /** @@ -179,56 +207,72 @@ s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data) **/ s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data) { + u32 i, mdic = 0, retry_counter, retry_max; struct e1000_phy_info *phy = &hw->phy; - u32 i, mdic = 0; + bool success; if (offset > MAX_PHY_REG_ADDRESS) { e_dbg("PHY Address %d is out of range\n", offset); return -E1000_ERR_PARAM; } + retry_max = phy->retry_enabled ? phy->retry_count : 0; + /* Set up Op-code, Phy Address, and register offset in the MDI * Control register. The MAC will take care of interfacing with the * PHY to retrieve the desired data. */ - mdic = (((u32)data) | - (offset << E1000_MDIC_REG_SHIFT) | - (phy->addr << E1000_MDIC_PHY_SHIFT) | - (E1000_MDIC_OP_WRITE)); + for (retry_counter = 0; retry_counter <= retry_max; retry_counter++) { + success = true; - ew32(MDIC, mdic); + mdic = (((u32)data) | + (offset << E1000_MDIC_REG_SHIFT) | + (phy->addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_WRITE)); - /* Poll the ready bit to see if the MDI read completed - * Increasing the time out as testing showed failures with - * the lower time out - */ - for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { - udelay(50); - mdic = er32(MDIC); - if (mdic & E1000_MDIC_READY) - break; - } - if (!(mdic & E1000_MDIC_READY)) { - e_dbg("MDI Write PHY Reg Address %d did not complete\n", offset); - return -E1000_ERR_PHY; - } - if (mdic & E1000_MDIC_ERROR) { - e_dbg("MDI Write PHY Red Address %d Error\n", offset); - return -E1000_ERR_PHY; - } - if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) { - e_dbg("MDI Write offset error - requested %d, returned %d\n", - offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic)); - return -E1000_ERR_PHY; - } + ew32(MDIC, mdic); - /* Allow some time after each MDIC transaction to avoid - * reading duplicate data in the next MDIC transaction. - */ - if (hw->mac.type == e1000_pch2lan) - udelay(100); + /* Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { + usleep_range(50, 60); + mdic = er32(MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + e_dbg("MDI Write PHY Reg Address %d did not complete\n", + offset); + success = false; + } + if (mdic & E1000_MDIC_ERROR) { + e_dbg("MDI Write PHY Reg Address %d Error\n", offset); + success = false; + } + if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) { + e_dbg("MDI Write offset error - requested %d, returned %d\n", + offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic)); + success = false; + } - return 0; + /* Allow some time after each MDIC transaction to avoid + * reading duplicate data in the next MDIC transaction. + */ + if (hw->mac.type == e1000_pch2lan) + usleep_range(100, 150); + + if (success) + return 0; + + if (retry_counter != retry_max) { + e_dbg("Perform retry on PHY transaction...\n"); + mdelay(10); + } + } + + return -E1000_ERR_PHY; } /** diff --git a/drivers/net/ethernet/intel/e1000e/phy.h b/drivers/net/ethernet/intel/e1000e/phy.h index c48777d09523..049bb325b4b1 100644 --- a/drivers/net/ethernet/intel/e1000e/phy.h +++ b/drivers/net/ethernet/intel/e1000e/phy.h @@ -51,6 +51,8 @@ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data); s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data); void e1000_power_up_phy_copper(struct e1000_hw *hw); void e1000_power_down_phy_copper(struct e1000_hw *hw); +void e1000e_disable_phy_retry(struct e1000_hw *hw); +void e1000e_enable_phy_retry(struct e1000_hw *hw); s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data); s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data); s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data); -- cgit v1.2.3 From 861e8086029e003305750b4126ecd6617465f5c7 Mon Sep 17 00:00:00 2001 From: Vitaly Lifshits Date: Sun, 3 Mar 2024 12:51:32 +0200 Subject: e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on some systems. It is suspected to be caused by initiating PHY transactions before the interface settles. Separating this configuration from the ULP enabling flow and moving it to the shutdown function allows enough time for the interface to settle and avoids adding a delay. Fixes: 6607c99e7034 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state") Co-developed-by: Dima Ruinskiy Signed-off-by: Dima Ruinskiy Signed-off-by: Vitaly Lifshits Tested-by: Naama Meir Signed-off-by: Tony Nguyen --- drivers/net/ethernet/intel/e1000e/ich8lan.c | 19 ------------------- drivers/net/ethernet/intel/e1000e/netdev.c | 18 ++++++++++++++++++ 2 files changed, 18 insertions(+), 19 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c index d8e97669f31b..f9e94be36e97 100644 --- a/drivers/net/ethernet/intel/e1000e/ich8lan.c +++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c @@ -1165,25 +1165,6 @@ s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx) if (ret_val) goto out; - /* Switching PHY interface always returns MDI error - * so disable retry mechanism to avoid wasting time - */ - e1000e_disable_phy_retry(hw); - - /* Force SMBus mode in PHY */ - ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg); - if (ret_val) - goto release; - phy_reg |= CV_SMB_CTRL_FORCE_SMBUS; - e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg); - - e1000e_enable_phy_retry(hw); - - /* Force SMBus mode in MAC */ - mac_reg = er32(CTRL_EXT); - mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; - ew32(CTRL_EXT, mac_reg); - /* Si workaround for ULP entry flow on i127/rev6 h/w. Enable * LPLU and disable Gig speed when entering ULP */ diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index cc8c531ec3df..3692fce20195 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -6623,6 +6623,7 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool runtime) struct e1000_hw *hw = &adapter->hw; u32 ctrl, ctrl_ext, rctl, status, wufc; int retval = 0; + u16 smb_ctrl; /* Runtime suspend should only enable wakeup for link changes */ if (runtime) @@ -6696,6 +6697,23 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool runtime) if (retval) return retval; } + + /* Force SMBUS to allow WOL */ + /* Switching PHY interface always returns MDI error + * so disable retry mechanism to avoid wasting time + */ + e1000e_disable_phy_retry(hw); + + e1e_rphy(hw, CV_SMB_CTRL, &smb_ctrl); + smb_ctrl |= CV_SMB_CTRL_FORCE_SMBUS; + e1e_wphy(hw, CV_SMB_CTRL, smb_ctrl); + + e1000e_enable_phy_retry(hw); + + /* Force SMBus mode in MAC */ + ctrl_ext = er32(CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_FORCE_SMBUS; + ew32(CTRL_EXT, ctrl_ext); } /* Ensure that the appropriate bits are set in LPI_CTRL -- cgit v1.2.3