dt-bindings: gpio: brcm,kona-gpio: convert to YAML

Convert Broadcom Kona family GPIO controller bindings to DT schema.

Changes during conversion:
  - add used, but previously undocumented SoC-specific compatibles

Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

2 files changed, 100 insertions, 52 deletions

diff --git a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
deleted file mode 100644
index 4a63bc96b687..000000000000
--- a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
+++ /dev/null
@@ -1,52 +0,0 @@
-Broadcom Kona Family GPIO
-=========================
-
-This GPIO driver is used in the following Broadcom SoCs:
-  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
-
-The Broadcom GPIO Controller IP can be configured prior to synthesis to
-support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
-GPIO controller only supports edge, not level, triggering of interrupts.
-
-Required properties
--------------------
-
-- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt outputs from the controller. There is one GPIO
-  interrupt per GPIO bank. The number of interrupts listed depends on the
-  number of GPIO banks on the SoC. The interrupts must be ordered by bank,
-  starting with bank 0. There is always a 1:1 mapping between banks and
-  IRQs.
-- #gpio-cells: Should be <2>. The first cell is the pin number, the second
-  cell is used to specify optional parameters:
-  - bit 0 specifies polarity (0 for normal, 1 for inverted)
-  See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
-- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
-  second cell is used to specify flags. The following subset of flags is
-  supported:
-  - trigger type (bits[1:0]):
-      1 = low-to-high edge triggered.
-      2 = high-to-low edge triggered.
-      3 = low-to-high or high-to-low edge triggered
-      Valid values are 1, 2, 3
-  See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
-- gpio-controller: Marks the device node as a GPIO controller.
-- interrupt-controller: Marks the device node as an interrupt controller.
-
-Example:
-	gpio: gpio@35003000 {
-		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
-		reg = <0x35003000 0x800>;
-		interrupts =
-		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		interrupt-controller;
-	};
diff --git a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
new file mode 100644
index 000000000000..296fdd6b8f38
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
@@ -0,0 +1,100 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/brcm,kona-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom Kona family GPIO controller
+
+description:
+  The Broadcom GPIO Controller IP can be configured prior to synthesis to
+  support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+  GPIO controller only supports edge, not level, triggering of interrupts.
+
+maintainers:
+  - Ray Jui <rjui@broadcom.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - brcm,bcm11351-gpio
+          - brcm,bcm21664-gpio
+          - brcm,bcm23550-gpio
+      - const: brcm,kona-gpio
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 4
+    maxItems: 6
+    description:
+      The interrupt outputs from the controller. There is one GPIO interrupt
+      per GPIO bank. The number of interrupts listed depends on the number of
+      GPIO banks on the SoC. The interrupts must be ordered by bank, starting
+      with bank 0. There is always a 1:1 mapping between banks and IRQs.
+
+  '#gpio-cells':
+    const: 2
+
+  '#interrupt-cells':
+    const: 2
+
+  gpio-controller: true
+
+  interrupt-controller: true
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - '#gpio-cells'
+  - '#interrupt-cells'
+  - gpio-controller
+  - interrupt-controller
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,bcm11351-gpio
+    then:
+      properties:
+        interrupts:
+          minItems: 6
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - brcm,bcm21664-gpio
+              - brcm,bcm23550-gpio
+    then:
+      properties:
+        interrupts:
+          maxItems: 4
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    gpio@35003000 {
+        compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+        reg = <0x35003000 0x800>;
+        interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+        #gpio-cells = <2>;
+        #interrupt-cells = <2>;
+        gpio-controller;
+        interrupt-controller;
+    };
+...