Merge branch 'next' into for-linus

4 files changed, 213 insertions, 19 deletions

diff --git a/Documentation/hwmon/amc6821 b/Documentation/hwmon/amc6821
new file mode 100644
index 000000000000..ced8359c50f8
--- /dev/null
+++ b/Documentation/hwmon/amc6821
@@ -0,0 +1,102 @@
+Kernel driver amc6821
+=====================
+
+Supported chips:
+	Texas Instruments AMC6821
+	Prefix: 'amc6821'
+	Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e
+	Datasheet: http://focus.ti.com/docs/prod/folders/print/amc6821.html
+
+Authors:
+	Tomaz Mertelj <tomaz.mertelj@guest.arnes.si>
+
+
+Description
+-----------
+
+This driver implements support for the Texas Instruments amc6821 chip.
+The chip has one on-chip and one remote temperature sensor and one pwm fan
+regulator.
+The pwm can be controlled either from software or automatically.
+
+The driver provides the following sensor accesses in sysfs:
+
+temp1_input		ro	on-chip temperature
+temp1_min		rw	"
+temp1_max		rw	"
+temp1_crit	 	rw	"
+temp1_min_alarm		ro	"
+temp1_max_alarm		ro	"
+temp1_crit_alarm	ro	"
+
+temp2_input		ro	remote temperature
+temp2_min		rw	"
+temp2_max		rw	"
+temp2_crit	 	rw	"
+temp2_min_alarm		ro	"
+temp2_max_alarm		ro	"
+temp2_crit_alarm	ro	"
+temp2_fault		ro	"
+
+fan1_input	 	ro	tachometer speed
+fan1_min		rw	"
+fan1_max		rw	"
+fan1_fault	 	ro	"
+fan1_div		rw	Fan divisor can be either 2 or 4.
+
+pwm1			rw	pwm1
+pwm1_enable		rw	regulator mode, 1=open loop, 2=fan controlled
+				by remote temperature, 3=fan controlled by
+				combination of the on-chip temperature and
+				remote-sensor temperature,
+pwm1_auto_channels_temp ro	1 if pwm_enable==2, 3 if pwm_enable==3
+pwm1_auto_point1_pwm	ro	Hardwired to 0, shared for both
+				temperature channels.
+pwm1_auto_point2_pwm	rw	This value is shared for both temperature
+				channels.
+pwm1_auto_point3_pwm	rw	Hardwired to 255, shared for both
+				temperature channels.
+
+temp1_auto_point1_temp	ro	Hardwired to temp2_auto_point1_temp
+				which is rw. Below this temperature fan stops.
+temp1_auto_point2_temp	rw	The low-temperature limit of the proportional
+				range. Below this temperature
+				pwm1 = pwm1_auto_point2_pwm. It can go from
+				0 degree C to 124 degree C in steps of
+				4 degree C. Read it out after writing to get
+				the actual value.
+temp1_auto_point3_temp	rw	Above this temperature fan runs at maximum
+				speed. It can go from temp1_auto_point2_temp.
+				It can only have certain discrete values
+				which depend on temp1_auto_point2_temp and
+				pwm1_auto_point2_pwm. Read it out after
+				writing to get the actual value.
+
+temp2_auto_point1_temp	rw	Must be between 0 degree C and 63 degree C and
+				it defines the passive cooling temperature.
+				Below this temperature the fan stops in
+				the closed loop mode.
+temp2_auto_point2_temp	rw	The low-temperature limit of the proportional
+				range. Below this temperature
+				pwm1 = pwm1_auto_point2_pwm. It can go from
+				0 degree C to 124 degree C in steps
+				of 4 degree C.
+
+temp2_auto_point3_temp	rw	Above this temperature fan runs at maximum
+				speed. It can only have certain discrete
+				values which depend on temp2_auto_point2_temp
+				and pwm1_auto_point2_pwm. Read it out after
+				writing to get actual value.
+
+
+Module parameters
+-----------------
+
+If your board has a BIOS that initializes the amc6821 correctly, you should
+load the module with: init=0.
+
+If your board BIOS doesn't initialize the chip, or you want
+different settings, you can set the following parameters:
+init=1,
+pwminv: 0 default pwm output, 1 inverts pwm output.
+
diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp
new file mode 100644
index 000000000000..6526eee525a6
--- /dev/null
+++ b/Documentation/hwmon/k10temp
@@ -0,0 +1,65 @@
+Kernel driver k10temp
+=====================
+
+Supported chips:
+* AMD Family 10h processors:
+  Socket F: Quad-Core/Six-Core/Embedded Opteron (but see below)
+  Socket AM2+: Quad-Core Opteron, Phenom (II) X3/X4, Athlon X2 (but see below)
+  Socket AM3: Quad-Core Opteron, Athlon/Phenom II X2/X3/X4, Sempron II
+  Socket S1G3: Athlon II, Sempron, Turion II
+* AMD Family 11h processors:
+  Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra)
+
+  Prefix: 'k10temp'
+  Addresses scanned: PCI space
+  Datasheets:
+  BIOS and Kernel Developer's Guide (BKDG) For AMD Family 10h Processors:
+    http://support.amd.com/us/Processor_TechDocs/31116.pdf
+  BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors:
+    http://support.amd.com/us/Processor_TechDocs/41256.pdf
+  Revision Guide for AMD Family 10h Processors:
+    http://support.amd.com/us/Processor_TechDocs/41322.pdf
+  Revision Guide for AMD Family 11h Processors:
+    http://support.amd.com/us/Processor_TechDocs/41788.pdf
+  AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks:
+    http://support.amd.com/us/Processor_TechDocs/43373.pdf
+  AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet:
+    http://support.amd.com/us/Processor_TechDocs/43374.pdf
+  AMD Family 10h Desktop Processor Power and Thermal Data Sheet:
+    http://support.amd.com/us/Processor_TechDocs/43375.pdf
+
+Author: Clemens Ladisch <clemens@ladisch.de>
+
+Description
+-----------
+
+This driver permits reading of the internal temperature sensor of AMD
+Family 10h and 11h processors.
+
+All these processors have a sensor, but on those for Socket F or AM2+,
+the sensor may return inconsistent values (erratum 319).  The driver
+will refuse to load on these revisions unless you specify the "force=1"
+module parameter.
+
+Due to technical reasons, the driver can detect only the mainboard's
+socket type, not the processor's actual capabilities.  Therefore, if you
+are using an AM3 processor on an AM2+ mainboard, you can safely use the
+"force=1" parameter.
+
+There is one temperature measurement value, available as temp1_input in
+sysfs. It is measured in degrees Celsius with a resolution of 1/8th degree.
+Please note that it is defined as a relative value; to quote the AMD manual:
+
+  Tctl is the processor temperature control value, used by the platform to
+  control cooling systems. Tctl is a non-physical temperature on an
+  arbitrary scale measured in degrees. It does _not_ represent an actual
+  physical temperature like die or case temperature. Instead, it specifies
+  the processor temperature relative to the point at which the system must
+  supply the maximum cooling for the processor's specified maximum case
+  temperature and maximum thermal power dissipation.
+
+The maximum value for Tctl is available in the file temp1_max.
+
+If the BIOS has enabled hardware temperature control, the threshold at
+which the processor will throttle itself to avoid damage is available in
+temp1_crit and temp1_crit_hyst.
diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d
index effe949a7282..06534f25e643 100644
--- a/Documentation/hwmon/lis3lv02d
+++ b/Documentation/hwmon/lis3lv02d
@@ -3,7 +3,8 @@ Kernel driver lis3lv02d
 
 Supported chips:
 
-  * STMicroelectronics LIS3LV02DL and LIS3LV02DQ
+  * STMicroelectronics LIS3LV02DL, LIS3LV02DQ (12 bits precision)
+  * STMicroelectronics LIS302DL, LIS3L02DQ, LIS331DL (8 bits)
 
 Authors:
         Yan Burman <burman.yan@gmail.com>
@@ -13,32 +14,52 @@ Authors:
 Description
 -----------
 
-This driver provides support for the accelerometer found in various HP
-laptops sporting the feature officially called "HP Mobile Data
-Protection System 3D" or "HP 3D DriveGuard". It detects automatically
-laptops with this sensor. Known models (for now the HP 2133, nc6420,
-nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis
-automatically oriented on standard way (eg: you can directly play
-neverball).  The accelerometer data is readable via
-/sys/devices/platform/lis3lv02d.
+This driver provides support for the accelerometer found in various HP laptops
+sporting the feature officially called "HP Mobile Data Protection System 3D" or
+"HP 3D DriveGuard". It detects automatically laptops with this sensor. Known
+models (full list can be found in drivers/hwmon/hp_accel.c) will have their
+axis automatically oriented on standard way (eg: you can directly play
+neverball). The accelerometer data is readable via
+/sys/devices/platform/lis3lv02d. Reported values are scaled
+to mg values (1/1000th of earth gravity).
 
 Sysfs attributes under /sys/devices/platform/lis3lv02d/:
 position - 3D position that the accelerometer reports. Format: "(x,y,z)"
-calibrate - read: values (x, y, z) that are used as the base for input
-		  class device operation.
-            write: forces the base to be recalibrated with the current
-		   position.
-rate - reports the sampling rate of the accelerometer device in HZ
+rate - read reports the sampling rate of the accelerometer device in HZ.
+	write changes sampling rate of the accelerometer device.
+	Only values which are supported by HW are accepted.
+selftest - performs selftest for the chip as specified by chip manufacturer.
 
 This driver also provides an absolute input class device, allowing
-the laptop to act as a pinball machine-esque joystick.
+the laptop to act as a pinball machine-esque joystick. Joystick device can be
+calibrated. Joystick device can be in two different modes.
+By default output values are scaled between -32768 .. 32767. In joystick raw
+mode, joystick and sysfs position entry have the same scale. There can be
+small difference due to input system fuzziness feature.
+Events are also available as input event device.
+
+Selftest is meant only for hardware diagnostic purposes. It is not meant to be
+used during normal operations. Position data is not corrupted during selftest
+but interrupt behaviour is not guaranteed to work reliably. In test mode, the
+sensing element is internally moved little bit. Selftest measures difference
+between normal mode and test mode. Chip specifications tell the acceptance
+limit for each type of the chip. Limits are provided via platform data
+to allow adjustment of the limits without a change to the actual driver.
+Seltest returns either "OK x y z" or "FAIL x y z" where x, y and z are
+measured difference between modes. Axes are not remapped in selftest mode.
+Measurement values are provided to help HW diagnostic applications to make
+final decision.
+
+On HP laptops, if the led infrastructure is activated, support for a led
+indicating disk protection will be provided as /sys/class/leds/hp::hddprotect.
 
 Another feature of the driver is misc device called "freefall" that
 acts similar to /dev/rtc and reacts on free-fall interrupts received
 from the device. It supports blocking operations, poll/select and
 fasync operation modes. You must read 1 bytes from the device.  The
 result is number of free-fall interrupts since the last successful
-read (or 255 if number of interrupts would not fit).
+read (or 255 if number of interrupts would not fit). See the hpfall.c
+file for an example on using the device.
 
 
 Axes orientation
@@ -55,7 +76,7 @@ the accelerometer are converted into a "standard" organisation of the axes
  * If the laptop is put upside-down, Z becomes negative
 
 If your laptop model is not recognized (cf "dmesg"), you can send an
-email to the authors to add it to the database.  When reporting a new
+email to the maintainer to add it to the database.  When reporting a new
 laptop, please include the output of "dmidecode" plus the value of
 /sys/devices/platform/lis3lv02d/position in these four cases.
 
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index 02b74899edaf..b7e42ec4b26b 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -81,8 +81,14 @@ pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range:
 	   0 (stop) to 255 (full)
 
 pwm[1-4]_enable - this file controls mode of fan/temperature control:
-	* 1 Manual Mode, write to pwm file any value 0-255 (full speed)
-	* 2 Thermal Cruise
+	* 1 Manual mode, write to pwm file any value 0-255 (full speed)
+	* 2 "Thermal Cruise" mode
+	* 3 "Fan Speed Cruise" mode
+	* 4 "Smart Fan III" mode
+
+pwm[1-4]_mode - controls if output is PWM or DC level
+        * 0 DC output (0 - 12v)
+        * 1 PWM output
 
 Thermal Cruise mode
 -------------------