Merge series "Support ROHM BD71815 PMIC" from Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>:

Patch series introducing support for ROHM BD71815 PMIC

ROHM BD71815 is a power management IC used in some battery powered
systems. It contains regulators, GPO(s), charger + coulomb counter, RTC
and a clock gate.

All regulators can be controlled via I2C. LDO4 can additionally be set to
be enabled/disabled by a GPIO. LDO3 voltage could be selected from two
voltages written into separate VSEL reisters using GPIO but this mode is
not supported by driver. On top of that the PMIC has the typical HW
state machine which is present also on many other ROHM PMICs.

IC contains two GPOs - but one of the GPOs is marked as GND in
data-sheet. Thus the driver by default only exposes one GPO. The second
GPO can be enabled by special DT property.

RTC is almost similar to what is on BD71828. For currently used features
only the register address offset to RTC block differs.

The charger driver is not included in this series. ROHM has a charger
driver with some fuel-gauging logig written in but this is not included
here. I am working on separating the logic from HW specific driver and
supporting both BD71815 and BD71828 chargers in separate patch series.

Changelog v5:
  Regulator:
  - Added regmap helper for regulator ramp-delay and taken it in use
    (patches 13, 14, 16 - they can be just dropped if ramp-delay helper is not
    a good idea. Patch 15 implements old-fashioned ramp-delay)
  GPIO:
  - styling changes to GPIO (Mostly suggested by Andy)
  - implemented init_valid_mask (but can't count on it yet)
Changelog v4:
  - Sorted ROHM chip ID enum
  - Statcized DVS structures in regulator driver
  - Minor styling for regulator driver
  - rebased on v5.12-rc4
Changelog v3:
  - GPIO clean-up as suggested by Bartosz
  - MFD clean-up as suggested by Lee
  - clk-mode dt-binding handling in MFD driver corrected to reflect new
    property values.
  - Dropped already applied patches
  - Rebased on v5.12-rc2
Changelog v2:
  - Rebased on top of v5.11-rc3
  - Added another "preliminary patch" which fixes HW-dvs voltage
    handling (patch 1)
  - split regulator patch to two.
  - changed dt-binding patch ordering.
  regulators:
    - staticized probe
    - removed some unnecessary defines
    - updated comments
    - split rohm-regulator patch adding SNVS and supporting simple
      linear mapping into two - one adding support for mapping, other
      adding SNVS.
  GPIO:
    - removed unnecessary headers
    - clarified dev/parent->dev usage
    - removed forgotten #define DEBUG
  dt-bindings:
    - changed patch order to meet ref-dependencies
    - added missing regulator nodes
    - changed string property for clk mode to tristated
  MFD:
    - header cleanups.
  CLK:
    - fixed commit message

--

Matti Vaittinen (19):
  rtc: bd70528: Do not require parent data
  mfd: bd718x7: simplify by cleaning unnecessary device data
  dt_bindings: bd71828: Add clock output mode
  dt_bindings: regulator: Add ROHM BD71815 PMIC regulators
  dt_bindings: mfd: Add ROHM BD71815 PMIC
  mfd: Add ROHM BD71815 ID
  mfd: Sort ROHM chip ID list for better readability
  mfd: Support for ROHM BD71815 PMIC core
  gpio: support ROHM BD71815 GPOs
  regulator: helpers: Export helper voltage listing
  regulator: rohm-regulator: linear voltage support
  regulator: rohm-regulator: Support SNVS HW state.
  regulator: Add regmap helper for ramp-delay setting
  regulator: bd718x7, bd71828: Use ramp-delay helper
  regulator: Support ROHM BD71815 regulators
  regulator: bd71815: use ramp-delay helper
  clk: bd718x7: Add support for clk gate on ROHM BD71815 PMIC
  rtc: bd70528: Support RTC on ROHM BD71815
  MAINTAINERS: Add ROHM BD71815AGW

 .../bindings/mfd/rohm,bd71815-pmic.yaml       | 201 ++++++
 .../bindings/mfd/rohm,bd71828-pmic.yaml       |   6 +
 .../regulator/rohm,bd71815-regulator.yaml     | 116 ++++
 MAINTAINERS                                   |   3 +
 drivers/clk/clk-bd718x7.c                     |   9 +-
 drivers/gpio/Kconfig                          |  10 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/gpio-bd71815.c                   | 193 ++++++
 drivers/mfd/Kconfig                           |  15 +-
 drivers/mfd/rohm-bd71828.c                    | 486 +++++++++----
 drivers/mfd/rohm-bd718x7.c                    |  43 +-
 drivers/regulator/Kconfig                     |  11 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/bd71815-regulator.c         | 651 ++++++++++++++++++
 drivers/regulator/bd71828-regulator.c         |  51 +-
 drivers/regulator/bd718x7-regulator.c         |  60 +-
 drivers/regulator/helpers.c                   | 101 ++-
 drivers/regulator/rohm-regulator.c            |  23 +-
 drivers/rtc/Kconfig                           |   6 +-
 drivers/rtc/rtc-bd70528.c                     | 104 +--
 include/linux/mfd/rohm-bd71815.h              | 562 +++++++++++++++
 include/linux/mfd/rohm-bd71828.h              |   3 +
 include/linux/mfd/rohm-bd718x7.h              |  13 -
 include/linux/mfd/rohm-generic.h              |  15 +-
 include/linux/regulator/driver.h              |   7 +
 25 files changed, 2393 insertions(+), 298 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml
 create mode 100644 drivers/gpio/gpio-bd71815.c
 create mode 100644 drivers/regulator/bd71815-regulator.c
 create mode 100644 include/linux/mfd/rohm-bd71815.h

base-commit: 0d02ec6b3136c73c09e7859f0d0e4e2c4c07b49b
--
2.25.4

--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]

2 files changed, 94 insertions, 9 deletions

diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c
index f42b394a0c46..0e16e31c968f 100644
--- a/drivers/regulator/helpers.c
+++ b/drivers/regulator/helpers.c
@@ -509,6 +509,33 @@ int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev,
 EXPORT_SYMBOL_GPL(regulator_map_voltage_pickable_linear_range);
 
 /**
+ * regulator_desc_list_voltage_linear - List voltages with simple calculation
+ *
+ * @desc: Regulator desc for regulator which volatges are to be listed
+ * @selector: Selector to convert into a voltage
+ *
+ * Regulators with a simple linear mapping between voltages and
+ * selectors can set min_uV and uV_step in the regulator descriptor
+ * and then use this function prior regulator registration to list
+ * the voltages. This is useful when voltages need to be listed during
+ * device-tree parsing.
+ */
+int regulator_desc_list_voltage_linear(const struct regulator_desc *desc,
+				       unsigned int selector)
+{
+	if (selector >= desc->n_voltages)
+		return -EINVAL;
+
+	if (selector < desc->linear_min_sel)
+		return 0;
+
+	selector -= desc->linear_min_sel;
+
+	return desc->min_uV + (desc->uV_step * selector);
+}
+EXPORT_SYMBOL_GPL(regulator_desc_list_voltage_linear);
+
+/**
  * regulator_list_voltage_linear - List voltages with simple calculation
  *
  * @rdev: Regulator device
@@ -521,14 +548,7 @@ EXPORT_SYMBOL_GPL(regulator_map_voltage_pickable_linear_range);
 int regulator_list_voltage_linear(struct regulator_dev *rdev,
 				  unsigned int selector)
 {
-	if (selector >= rdev->desc->n_voltages)
-		return -EINVAL;
-	if (selector < rdev->desc->linear_min_sel)
-		return 0;
-
-	selector -= rdev->desc->linear_min_sel;
-
-	return rdev->desc->min_uV + (rdev->desc->uV_step * selector);
+	return regulator_desc_list_voltage_linear(rdev->desc, selector);
 }
 EXPORT_SYMBOL_GPL(regulator_list_voltage_linear);
 
@@ -881,3 +901,68 @@ bool regulator_is_equal(struct regulator *reg1, struct regulator *reg2)
 	return reg1->rdev == reg2->rdev;
 }
 EXPORT_SYMBOL_GPL(regulator_is_equal);
+
+static int find_closest_bigger(unsigned int target, const unsigned int *table,
+			       unsigned int num_sel, unsigned int *sel)
+{
+	unsigned int s, tmp, max, maxsel = 0;
+	bool found = false;
+
+	max = table[0];
+
+	for (s = 0; s < num_sel; s++) {
+		if (table[s] > max) {
+			max = table[s];
+			maxsel = s;
+		}
+		if (table[s] >= target) {
+			if (!found || table[s] - target < tmp - target) {
+				tmp = table[s];
+				*sel = s;
+				found = true;
+				if (tmp == target)
+					break;
+			}
+		}
+	}
+
+	if (!found) {
+		*sel = maxsel;
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * regulator_set_ramp_delay_regmap - set_ramp_delay() helper
+ *
+ * @rdev: regulator to operate on
+ *
+ * Regulators that use regmap for their register I/O can set the ramp_reg
+ * and ramp_mask fields in their descriptor and then use this as their
+ * set_ramp_delay operation, saving some code.
+ */
+int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay)
+{
+	int ret;
+	unsigned int sel;
+
+	if (!rdev->desc->n_ramp_values)
+		return -EINVAL;
+
+	ret = find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
+				  rdev->desc->n_ramp_values, &sel);
+
+	if (ret) {
+		dev_warn(rdev_get_dev(rdev),
+			 "Can't set ramp-delay %u, setting %u\n", ramp_delay,
+			 rdev->desc->ramp_delay_table[sel]);
+	}
+
+	sel <<= ffs(rdev->desc->ramp_mask) - 1;
+
+	return regmap_update_bits(rdev->regmap, rdev->desc->ramp_reg,
+				  rdev->desc->ramp_mask, sel);
+}
+EXPORT_SYMBOL_GPL(regulator_set_ramp_delay_regmap);
diff --git a/drivers/regulator/mt6315-regulator.c b/drivers/regulator/mt6315-regulator.c
index fc7654624dd6..9edc34981ee0 100644
--- a/drivers/regulator/mt6315-regulator.c
+++ b/drivers/regulator/mt6315-regulator.c
@@ -41,7 +41,7 @@ struct mt6315_chip {
 		.type = REGULATOR_VOLTAGE,			\
 		.id = _bid,					\
 		.owner = THIS_MODULE,				\
-		.n_voltages = 0xbf,				\
+		.n_voltages = 0xc0,				\
 		.linear_ranges = mt_volt_range1,		\
 		.n_linear_ranges = ARRAY_SIZE(mt_volt_range1),	\
 		.vsel_reg = _vsel,				\