diff options
Diffstat (limited to 'Documentation/devicetree/bindings/misc')
3 files changed, 92 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt new file mode 100644 index 000000000000..1442ba5d2d98 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt @@ -0,0 +1,11 @@ +DPAA2 console support + +Required properties: + + - compatible + Value type: <string> + Definition: Must be "fsl,dpaa2-console". + - reg + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the region where the MCFBA + (MC firmware base address) register can be found. diff --git a/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt new file mode 100644 index 000000000000..8c4d649cdd8f --- /dev/null +++ b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt @@ -0,0 +1,23 @@ +OLPC XO-1.75 Embedded Controller + +Required properties: +- compatible: Should be "olpc,xo1.75-ec". +- cmd-gpios: gpio specifier of the CMD pin + +The embedded controller requires the SPI controller driver to signal readiness +to receive a transfer (that is, when TX FIFO contains the response data) by +strobing the ACK pin with the ready signal. See the "ready-gpios" property of the +SSP binding as documented in: +<Documentation/devicetree/bindings/spi/spi-pxa2xx.txt>. + +Example: + &ssp3 { + spi-slave; + ready-gpios = <&gpio 125 GPIO_ACTIVE_HIGH>; + + slave { + compatible = "olpc,xo1.75-ec"; + spi-cpha; + cmd-gpios = <&gpio 155 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt b/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt new file mode 100644 index 000000000000..e3289634fa30 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt @@ -0,0 +1,58 @@ +* Xilinx SDFEC(16nm) IP * + +The Soft Decision Forward Error Correction (SDFEC) Engine is a Hard IP block +which provides high-throughput LDPC and Turbo Code implementations. +The LDPC decode & encode functionality is capable of covering a range of +customer specified Quasi-cyclic (QC) codes. The Turbo decode functionality +principally covers codes used by LTE. The FEC Engine offers significant +power and area savings versus implementations done in the FPGA fabric. + + +Required properties: +- compatible: Must be "xlnx,sd-fec-1.1" +- clock-names : List of input clock names from the following: + - "core_clk", Main processing clock for processing core (required) + - "s_axi_aclk", AXI4-Lite memory-mapped slave interface clock (required) + - "s_axis_din_aclk", DIN AXI4-Stream Slave interface clock (optional) + - "s_axis_din_words-aclk", DIN_WORDS AXI4-Stream Slave interface clock (optional) + - "s_axis_ctrl_aclk", Control input AXI4-Stream Slave interface clock (optional) + - "m_axis_dout_aclk", DOUT AXI4-Stream Master interface clock (optional) + - "m_axis_dout_words_aclk", DOUT_WORDS AXI4-Stream Master interface clock (optional) + - "m_axis_status_aclk", Status output AXI4-Stream Master interface clock (optional) +- clocks : Clock phandles (see clock_bindings.txt for details). +- reg: Should contain Xilinx SDFEC 16nm Hardened IP block registers + location and length. +- xlnx,sdfec-code : Should contain "ldpc" or "turbo" to describe the codes + being used. +- xlnx,sdfec-din-words : A value 0 indicates that the DIN_WORDS interface is + driven with a fixed value and is not present on the device, a value of 1 + configures the DIN_WORDS to be block based, while a value of 2 configures the + DIN_WORDS input to be supplied for each AXI transaction. +- xlnx,sdfec-din-width : Configures the DIN AXI stream where a value of 1 + configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width + of "4x128b". +- xlnx,sdfec-dout-words : A value 0 indicates that the DOUT_WORDS interface is + driven with a fixed value and is not present on the device, a value of 1 + configures the DOUT_WORDS to be block based, while a value of 2 configures the + DOUT_WORDS input to be supplied for each AXI transaction. +- xlnx,sdfec-dout-width : Configures the DOUT AXI stream where a value of 1 + configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width + of "4x128b". +Optional properties: +- interrupts: should contain SDFEC interrupt number + +Example +--------------------------------------- + sd_fec_0: sd-fec@a0040000 { + compatible = "xlnx,sd-fec-1.1"; + clock-names = "core_clk","s_axi_aclk","s_axis_ctrl_aclk","s_axis_din_aclk","m_axis_status_aclk","m_axis_dout_aclk"; + clocks = <&misc_clk_2>,<&misc_clk_0>,<&misc_clk_1>,<&misc_clk_1>,<&misc_clk_1>, <&misc_clk_1>; + reg = <0x0 0xa0040000 0x0 0x40000>; + interrupt-parent = <&axi_intc>; + interrupts = <1 0>; + xlnx,sdfec-code = "ldpc"; + xlnx,sdfec-din-words = <0>; + xlnx,sdfec-din-width = <2>; + xlnx,sdfec-dout-words = <0>; + xlnx,sdfec-dout-width = <1>; + }; |