| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Export pcie_retrain_link() for use outside ASPM
- Add Data Link Layer Link Active Reporting as another way for
pcie_retrain_link() to determine the link is up
- Work around link training failures (especially on the ASMedia
ASM2824 switch) by training first at 2.5GT/s and then attempting
higher rates
Resource management:
- When we coalesce host bridge windows, remove invalidated resources
from the resource tree so future allocations work correctly
Hotplug:
- Cancel bringup sequence if card is not present, to keep from
blinking Power Indicator indefinitely
- Reassign bridge resources if necessary for ACPI hotplug
Driver binding:
- Convert platform_device .remove() callbacks to return void instead
of a mostly useless int
Power management:
- Reduce wait time for secondary bus to be ready to speed up resume
- Avoid putting EloPOS E2/S2/H2 (as well as Elo i2) PCIe Ports in
D3cold
- Call _REG when transitioning D-states so AML that uses the PCI
config space OpRegion works, which fixes some ASMedia GPIO
controllers after resume
Virtualization:
- Delay extra 250ms after FLR of Solidigm P44 Pro NVMe to avoid KVM
hang when guest is rebooted
- Add function 1 DMA alias quirk for Marvell 88SE9235
Error handling:
- Unexport pci_save_aer_state() since it's only used in drivers/pci/
- Drop recommendation for drivers to configure AER Capability, since
the PCI core does this for all devices
ASPM:
- Disable ASPM on MFD function removal to avoid use-after-free
- Tighten up pci_enable_link_state() and pci_disable_link_state()
interfaces so they don't enable/disable states the driver didn't
specify
- Avoid link retraining race that can happen if ASPM sets link
control parameters while the link is in the midst of training for
some other reason
Endpoint framework:
- Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be
different from "PCI Endpoint NTB driver"
- Automatically create a function specific attributes group for
endpoint drivers to avoid reference counting issues
- Fix many EPC test issues
- Return pci_epf_type_add_cfs() error if EPF has no driver
- Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq()
MSI vector parameters
- Pass EPF device ID to driver probe functions
- Return -EALREADY if EPC has already been started/stopped
- Add linkdown notifier support and use it in qcom-ep
- Add Bus Master Enable event support and use it in qcom-ep
- Add Qualcomm Modem Host Interface (MHI) endpoint driver
- Add Layerscape PME interrupt handling to manage link-up
notification
Cadence PCIe controller driver:
- Wait for link retrain to complete when working around the J721E
i2085 erratum with Gen2 mode
Faraday FTPC100 PCI controller driver:
- Release clock resources on error paths
Freescale i.MX6 PCIe controller driver:
- Save and restore Root Port MSI control to work around hardware defect
Intel VMD host bridge driver:
- Reset VMD config register between soft reboots
- Capture pci_reset_bus() return value instead of printing junk when
it fails
Qualcomm PCIe controller driver:
- Add SDX65 endpoint compatible string to DT binding
- Disable register write access after init for IP v2.3.3, v2.9.0
- Use DWC helpers for enabling/disabling writes to DBI registers
- Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2,
v2.3.3, v2.7.0, v2.9.0
- Reuse v2.3.2 post-init sequence for v2.4.0
Renesas R-Car PCIe controller driver:
- Remove unused static pcie_base and pcie_dev
Rockchip PCIe controller driver:
- Remove writes to unused registers
- Write endpoint Device ID using correct register
- Assert PCI Configuration Enable bit after probe so endpoint
responds instead of generating Request Retry Status messages
- Poll waiting for PHY PLLs to lock
- Update RK3399 example DT binding to be valid
- Use RK3399 PCIE_CLIENT_LEGACY_INT_CTRL to generate INTx instead of
manually generating PCIe message
- Use multiple windows to avoid address translation conflicts
- Use u32 (not u16) when accessing 32-bit registers
- Hide MSI-X Capability, since RK3399 can't generate MSI-X
- Set endpoint controller required alignment to 256
Synopsys DesignWare PCIe controller driver:
- Wait for link to come up only if we've initiated link training
Miscellaneous:
- Add pci_clear_master() stub for non-CONFIG_PCI"
* tag 'pci-v6.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
Documentation: PCI: correct spelling
PCI: vmd: Fix uninitialized variable usage in vmd_enable_domain()
PCI: xgene-msi: Convert to platform remove callback returning void
PCI: tegra: Convert to platform remove callback returning void
PCI: rockchip-host: Convert to platform remove callback returning void
PCI: mvebu: Convert to platform remove callback returning void
PCI: mt7621: Convert to platform remove callback returning void
PCI: mediatek-gen3: Convert to platform remove callback returning void
PCI: mediatek: Convert to platform remove callback returning void
PCI: iproc: Convert to platform remove callback returning void
PCI: hisi-error: Convert to platform remove callback returning void
PCI: dwc: Convert to platform remove callback returning void
PCI: j721e: Convert to platform remove callback returning void
PCI: brcmstb: Convert to platform remove callback returning void
PCI: altera-msi: Convert to platform remove callback returning void
PCI: altera: Convert to platform remove callback returning void
PCI: aardvark: Convert to platform remove callback returning void
PCI: rcar: Use correct product family name for Renesas R-Car
PCI: layerscape: Add the endpoint linkup notifier support
PCI: endpoint: pci-epf-vntb: Fix typo in comments
...
|
|
Pull rdma updates from Jason Gunthorpe:
"This cycle saw a focus on rxe and bnxt_re drivers:
- Code cleanups for irdma, rxe, rtrs, hns, vmw_pvrdma
- rxe uses workqueues instead of tasklets
- rxe has better compliance around access checks for MRs and rereg_mr
- mana supportst he 'v2' FW interface for RX coalescing
- hfi1 bug fix for stale cache entries in its MR cache
- mlx5 buf fix to handle FW failures when destroying QPs
- erdma HW has a new doorbell allocation mechanism for uverbs that is
secure
- Lots of small cleanups and rework in bnxt_re:
- Use the common mmap functions
- Support disassociation
- Improve FW command flow
- support for 'low latency push'"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (71 commits)
RDMA/bnxt_re: Fix an IS_ERR() vs NULL check
RDMA/bnxt_re: Fix spelling mistake "priviledged" -> "privileged"
RDMA/bnxt_re: Remove duplicated include in bnxt_re/main.c
RDMA/bnxt_re: Refactor code around bnxt_qplib_map_rc()
RDMA/bnxt_re: Remove incorrect return check from slow path
RDMA/bnxt_re: Enable low latency push
RDMA/bnxt_re: Reorg the bar mapping
RDMA/bnxt_re: Move the interface version to chip context structure
RDMA/bnxt_re: Query function capabilities from firmware
RDMA/bnxt_re: Optimize the bnxt_re_init_hwrm_hdr usage
RDMA/bnxt_re: Add disassociate ucontext support
RDMA/bnxt_re: Use the common mmap helper functions
RDMA/bnxt_re: Initialize opcode while sending message
RDMA/cma: Remove NULL check before dev_{put, hold}
RDMA/rxe: Simplify cq->notify code
RDMA/rxe: Fixes mr access supported list
RDMA/bnxt_re: optimize the parameters passed to helper functions
RDMA/bnxt_re: remove redundant cmdq_bitmap
RDMA/bnxt_re: use firmware provided max request timeout
RDMA/bnxt_re: cancel all control path command waiters upon error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"There are three areas of note:
A bunch of strlcpy()->strscpy() conversions ended up living in my tree
since they were either Acked by maintainers for me to carry, or got
ignored for multiple weeks (and were trivial changes).
The compiler option '-fstrict-flex-arrays=3' has been enabled
globally, and has been in -next for the entire devel cycle. This
changes compiler diagnostics (though mainly just -Warray-bounds which
is disabled) and potential UBSAN_BOUNDS and FORTIFY _warning_
coverage. In other words, there are no new restrictions, just
potentially new warnings. Any new FORTIFY warnings we've seen have
been fixed (usually in their respective subsystem trees). For more
details, see commit df8fc4e934c12b.
The under-development compiler attribute __counted_by has been added
so that we can start annotating flexible array members with their
associated structure member that tracks the count of flexible array
elements at run-time. It is possible (likely?) that the exact syntax
of the attribute will change before it is finalized, but GCC and Clang
are working together to sort it out. Any changes can be made to the
macro while we continue to add annotations.
As an example of that last case, I have a treewide commit waiting with
such annotations found via Coccinelle:
https://git.kernel.org/linus/adc5b3cb48a049563dc673f348eab7b6beba8a9b
Also see commit dd06e72e68bcb4 for more details.
Summary:
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex
arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members"
* tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (54 commits)
netfilter: ipset: Replace strlcpy with strscpy
uml: Replace strlcpy with strscpy
um: Use HOST_DIR for mrproper
kallsyms: Replace all non-returning strlcpy with strscpy
sh: Replace all non-returning strlcpy with strscpy
of/flattree: Replace all non-returning strlcpy with strscpy
sparc64: Replace all non-returning strlcpy with strscpy
Hexagon: Replace all non-returning strlcpy with strscpy
kobject: Use return value of strreplace()
lib/string_helpers: Change returned value of the strreplace()
jbd2: Avoid printing outside the boundary of the buffer
checkpatch: Check for 0-length and 1-element arrays
riscv/purgatory: Do not use fortified string functions
s390/purgatory: Do not use fortified string functions
x86/purgatory: Do not use fortified string functions
acpi: Replace struct acpi_table_slit 1-element array with flex-array
clocksource: Replace all non-returning strlcpy with strscpy
string: use __builtin_memcpy() in strlcpy/strlcat
staging: most: Replace all non-returning strlcpy with strscpy
drm/i2c: tda998x: Replace all non-returning strlcpy with strscpy
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull ordered workqueue creation updates from Tejun Heo:
"For historical reasons, unbound workqueues with max concurrency limit
of 1 are considered ordered, even though the concurrency limit hasn't
been system-wide for a long time.
This creates ambiguity around whether ordered execution is actually
required for correctness, which was actually confusing for e.g. btrfs
(btrfs updates are being routed through the btrfs tree).
There aren't that many users in the tree which use the combination and
there are pending improvements to unbound workqueue affinity handling
which will make inadvertent use of ordered workqueue a bigger loss.
This clarifies the situation for most of them by updating the ones
which require ordered execution to use alloc_ordered_workqueue().
There are some conversions being routed through subsystem-specific
trees and likely a few stragglers. Once they're all converted,
workqueue can trigger a warning on unbound + @max_active==1 usages and
eventually drop the implicit ordered behavior"
* tag 'wq-for-6.5-cleanup-ordered' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
rxrpc: Use alloc_ordered_workqueue() to create ordered workqueues
net: qrtr: Use alloc_ordered_workqueue() to create ordered workqueues
net: wwan: t7xx: Use alloc_ordered_workqueue() to create ordered workqueues
dm integrity: Use alloc_ordered_workqueue() to create ordered workqueues
media: amphion: Use alloc_ordered_workqueue() to create ordered workqueues
scsi: NCR5380: Use default @max_active for hostdata->work_q
media: coda: Use alloc_ordered_workqueue() to create ordered workqueues
crypto: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueues
wifi: ath10/11/12k: Use alloc_ordered_workqueue() to create ordered workqueues
wifi: mwifiex: Use default @max_active for workqueues
wifi: iwlwifi: Use default @max_active for trans_pcie->rba.alloc_wq
xen/pvcalls: Use alloc_ordered_workqueue() to create ordered workqueues
virt: acrn: Use alloc_ordered_workqueue() to create ordered workqueues
net: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueues
net: thunderx: Use alloc_ordered_workqueue() to create ordered workqueues
greybus: Use alloc_ordered_workqueue() to create ordered workqueues
powerpc, workqueue: Use alloc_ordered_workqueue() to create ordered workqueues
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into soc/drivers
NXP/FSL SoC driver updates for v6.5
- fsl-mc: Make remove function return void
- QE USB: fix build issue caused by missing dependency
* tag 'soc-fsl-next-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
bus: fsl-mc: fsl-mc-allocator: Drop a write-only variable
bus: fsl-mc: fsl-mc-allocator: Initialize mc_bus_dev before use
soc/fsl/qe: fix usb.c build errors
bus: fsl-mc: Make remove function return void
soc: fsl: dpio: Suppress duplicated error reporting on device remove
bus: fsl-mc: fsl-mc-allocator: Improve error reporting
bus: fsl-mc: fsl-mc-allocator: Drop if block with always wrong condition
bus: fsl-mc: dprc: Push down error message from fsl_mc_driver_remove()
bus: fsl-mc: Only warn once about errors on device unbind
Link: https://lore.kernel.org/r/20230621222503.12402-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Linux 6.4
Resolve conflicts between rdma rc and next in rxe_cq matching linux-next:
drivers/infiniband/sw/rxe/rxe_cq.c:
https://lore.kernel.org/r/20230622115246.365d30ad@canb.auug.org.au
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Simplify comparison, no functional changes.
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
Link: https://lore.kernel.org/r/20230627035432.1296760-1-moritzf@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes to prepare for the 6.5 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Two deadly typos break RX and TX traffic on the VSC8502 PHY using RGMII
if phy-mode = "rgmii-id" or "rgmii-txid", and no "tx-internal-delay-ps"
override exists. The negative error code from phy_get_internal_delay()
does not get overridden with the delay deduced from the phy-mode, and
later gets committed to hardware. Also, the rx_delay gets overridden by
what should have been the tx_delay.
Fixes: dbb050d2bfc8 ("phy: mscc: Add support for RGMII delay configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230627134235.3453358-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vmalloc_array and vcalloc to protect against
multiplication overflows.
The changes were done using the following Coccinelle
semantic patch:
// <smpl>
@initialize:ocaml@
@@
let rename alloc =
match alloc with
"vmalloc" -> "vmalloc_array"
| "vzalloc" -> "vcalloc"
| _ -> failwith "unknown"
@@
size_t e1,e2;
constant C1, C2;
expression E1, E2, COUNT, x1, x2, x3;
typedef u8;
typedef __u8;
type t = {u8,__u8,char,unsigned char};
identifier alloc = {vmalloc,vzalloc};
fresh identifier realloc = script:ocaml(alloc) { rename alloc };
@@
(
alloc(x1*x2*x3)
|
alloc(C1 * C2)
|
alloc((sizeof(t)) * (COUNT), ...)
|
- alloc((e1) * (e2))
+ realloc(e1, e2)
|
- alloc((e1) * (COUNT))
+ realloc(COUNT, e1)
|
- alloc((E1) * (E2))
+ realloc(E1, E2)
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230627144339.144478-23-Julia.Lawall@inria.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vmalloc_array and vcalloc to protect against
multiplication overflows.
The changes were done using the following Coccinelle
semantic patch:
// <smpl>
@initialize:ocaml@
@@
let rename alloc =
match alloc with
"vmalloc" -> "vmalloc_array"
| "vzalloc" -> "vcalloc"
| _ -> failwith "unknown"
@@
size_t e1,e2;
constant C1, C2;
expression E1, E2, COUNT, x1, x2, x3;
typedef u8;
typedef __u8;
type t = {u8,__u8,char,unsigned char};
identifier alloc = {vmalloc,vzalloc};
fresh identifier realloc = script:ocaml(alloc) { rename alloc };
@@
(
alloc(x1*x2*x3)
|
alloc(C1 * C2)
|
alloc((sizeof(t)) * (COUNT), ...)
|
- alloc((e1) * (e2))
+ realloc(e1, e2)
|
- alloc((e1) * (COUNT))
+ realloc(COUNT, e1)
|
- alloc((E1) * (E2))
+ realloc(E1, E2)
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230627144339.144478-19-Julia.Lawall@inria.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vmalloc_array and vcalloc to protect against
multiplication overflows.
The changes were done using the following Coccinelle
semantic patch:
// <smpl>
@initialize:ocaml@
@@
let rename alloc =
match alloc with
"vmalloc" -> "vmalloc_array"
| "vzalloc" -> "vcalloc"
| _ -> failwith "unknown"
@@
size_t e1,e2;
constant C1, C2;
expression E1, E2, COUNT, x1, x2, x3;
typedef u8;
typedef __u8;
type t = {u8,__u8,char,unsigned char};
identifier alloc = {vmalloc,vzalloc};
fresh identifier realloc = script:ocaml(alloc) { rename alloc };
@@
(
alloc(x1*x2*x3)
|
alloc(C1 * C2)
|
alloc((sizeof(t)) * (COUNT), ...)
|
- alloc((e1) * (e2))
+ realloc(e1, e2)
|
- alloc((e1) * (COUNT))
+ realloc(COUNT, e1)
|
- alloc((E1) * (E2))
+ realloc(E1, E2)
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230627144339.144478-12-Julia.Lawall@inria.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vmalloc_array and vcalloc to protect against
multiplication overflows.
The changes were done using the following Coccinelle
semantic patch:
// <smpl>
@initialize:ocaml@
@@
let rename alloc =
match alloc with
"vmalloc" -> "vmalloc_array"
| "vzalloc" -> "vcalloc"
| _ -> failwith "unknown"
@@
size_t e1,e2;
constant C1, C2;
expression E1, E2, COUNT, x1, x2, x3;
typedef u8;
typedef __u8;
type t = {u8,__u8,char,unsigned char};
identifier alloc = {vmalloc,vzalloc};
fresh identifier realloc = script:ocaml(alloc) { rename alloc };
@@
(
alloc(x1*x2*x3)
|
alloc(C1 * C2)
|
alloc((sizeof(t)) * (COUNT), ...)
|
- alloc((e1) * (e2))
+ realloc(e1, e2)
|
- alloc((e1) * (COUNT))
+ realloc(COUNT, e1)
|
- alloc((E1) * (E2))
+ realloc(E1, E2)
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230627144339.144478-10-Julia.Lawall@inria.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vmalloc_array and vcalloc to protect against
multiplication overflows.
The changes were done using the following Coccinelle
semantic patch:
// <smpl>
@initialize:ocaml@
@@
let rename alloc =
match alloc with
"vmalloc" -> "vmalloc_array"
| "vzalloc" -> "vcalloc"
| _ -> failwith "unknown"
@@
size_t e1,e2;
constant C1, C2;
expression E1, E2, COUNT, x1, x2, x3;
typedef u8;
typedef __u8;
type t = {u8,__u8,char,unsigned char};
identifier alloc = {vmalloc,vzalloc};
fresh identifier realloc = script:ocaml(alloc) { rename alloc };
@@
(
alloc(x1*x2*x3)
|
alloc(C1 * C2)
|
alloc((sizeof(t)) * (COUNT), ...)
|
- alloc((e1) * (e2))
+ realloc(e1, e2)
|
- alloc((e1) * (COUNT))
+ realloc(COUNT, e1)
|
- alloc((E1) * (E2))
+ realloc(E1, E2)
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230627144339.144478-5-Julia.Lawall@inria.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vmalloc_array and vcalloc to protect against
multiplication overflows.
The changes were done using the following Coccinelle
semantic patch:
// <smpl>
@initialize:ocaml@
@@
let rename alloc =
match alloc with
"vmalloc" -> "vmalloc_array"
| "vzalloc" -> "vcalloc"
| _ -> failwith "unknown"
@@
size_t e1,e2;
constant C1, C2;
expression E1, E2, COUNT, x1, x2, x3;
typedef u8;
typedef __u8;
type t = {u8,__u8,char,unsigned char};
identifier alloc = {vmalloc,vzalloc};
fresh identifier realloc = script:ocaml(alloc) { rename alloc };
@@
(
alloc(x1*x2*x3)
|
alloc(C1 * C2)
|
alloc((sizeof(t)) * (COUNT), ...)
|
- alloc((e1) * (e2))
+ realloc(e1, e2)
|
- alloc((e1) * (COUNT))
+ realloc(COUNT, e1)
|
- alloc((E1) * (E2))
+ realloc(E1, E2)
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20230627144339.144478-3-Julia.Lawall@inria.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add RmNet support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20230626125336.3127-1-davide.tronchin.94@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ipvlan_queue_xmit() should return NET_XMIT_XXX, but
ipvlan_xmit_mode_l2/l3() returns rx_handler_result_t or NET_RX_XXX
in some cases. ipvlan_rcv_frame() will only return RX_HANDLER_CONSUMED
in ipvlan_xmit_mode_l2/l3() because 'local' is true. It's equal to
NET_XMIT_SUCCESS. But dev_forward_skb() can return NET_RX_SUCCESS or
NET_RX_DROP, and returning NET_RX_DROP(NET_XMIT_DROP) will increase
both ipvlan and ipvlan->phy_dev drops counter.
The skb to forward can be treated as xmitted successfully. This patch
makes ipvlan_queue_xmit() return NET_XMIT_SUCCESS for forward skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230626093347.7492-1-cambda@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These extend the int340x thermal driver, add thermal DT bindings for
some Qcom platforms, add DT bindings and support for Armada AP807 and
MSM8909, allow selecting the bang-bang thermal governor as the default
one, address issues in several thermal drivers for ARM platforms and
clean up code.
Specifics:
- Add new IOCTLs to the int340x thermal driver to allow user space to
retrieve the Passive v2 thermal table (Srinivas Pandruvada)
- Add DT bindings for SM6375, MSM8226 and QCM2290 Qcom platforms
(Konrad Dybcio)
- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki)
- Add DT bindings for QCom ipq9574 (Praveenkumar I)
- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren)
- Allow selecting the bang-bang governor as default (Thierry Reding)
- Refactor and prepare the code to set the scene for RCar Gen4
(Wolfram Sang)
- Clean up and fix the QCom tsens drivers. Add DT bindings and
calibration for the MSM8909 platform (Stephan Gerhold)
- Revert a patch introducing a wrong usage of devm_of_iomap() on the
Mediatek platform (Ricardo Cañuelo)
- Fix the clock vs reset ordering in order to conform to the
documentation on the sun8i (Christophe JAILLET)
- Prevent setting up undocumented registers, enable the only
described sensors and add the version 2.1 on the Qoriq sensor (Peng
Fan)
- Add DT bindings and support for the Armada AP807 (Alex Leibovich)
- Update the mlx5 driver with the recent thermal changes (Daniel
Lezcano)
- Convert to platform remove callback returning void on STM32 (Uwe
Kleine-König)
- Add an error information printing for devm_thermal_add_hwmon_sysfs()
and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
Qoriq, Mediateka and QCom (Yangtao Li)
- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai)
- Use the dev_err_probe() function in the QCom tsens alarm driver
(Luca Weiss)"
* tag 'thermal-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (39 commits)
thermal/drivers/qcom/temp-alarm: Use dev_err_probe
thermal/drivers/generic-adc: Register thermal zones as hwmon sensors
thermal/drivers/mediatek/lvts_thermal: Remove redundant msg in lvts_ctrl_start()
thermal/drivers/qcom: Remove redundant msg at probe time
thermal/drivers/ti-soc: Remove redundant msg in ti_thermal_expose_sensor()
thermal/drivers/qoriq: Remove redundant msg in qoriq_tmu_register_tmu_zone()
thermal/drivers/tegra: Remove redundant msg in tegra_tsensor_register_channel()
drivers/thermal/k3: Remove redundant msg in k3_bandgap_probe()
thermal/drivers/imx: Remove redundant msg in imx8mm_tmu_probe() and imx_sc_thermal_probe()
thermal/drivers/amlogic: Remove redundant msg in amlogic_thermal_probe()
thermal/drivers/sun8i: Remove redundant msg in sun8i_ths_register()
thermal/hwmon: Add error information printing for devm_thermal_add_hwmon_sysfs()
thermal/drivers/stm32: Convert to platform remove callback returning void
net/mlx5: Update the driver with the recent thermal changes
thermal/drivers/armada: Add support for AP807 thermal data
dt-bindings: armada-thermal: Add armada-ap807-thermal compatible
thermal/drivers/qoriq: Support version 2.1
thermal/drivers/qoriq: Only enable supported sensors
thermal/drivers/qoriq: No need to program site adjustment register
thermal/drivers/mediatek/lvts_thermal: Register thermal zones as hwmon sensors
...
|
|
The thermal framework is migrating to the generic trip points. The set
of changes also implies a self-encapsulation of the thermal zone
device structure where the internals are no longer directly accessible
but with accessors.
Use the new API instead, so the next changes can be pushed in the
thermal framework without this driver failing to compile.
No functional changes intended.
Cc: Sandipan Patra <spatra@nvidia.com>
Cc: Gal Pressman <gal@nvidia.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230525140135.3589917-2-daniel.lezcano@linaro.org
|
|
Add two bytes of padding to the start of struct ef4_loopback_payload,
which are not sent on the wire. This ensures the 'ip' member is
4-byte aligned, preventing the following W=1 warning:
net/ethernet/sfc/falcon/selftest.c:43:15: error: field ip within 'struct ef4_loopback_payload' is less aligned than 'struct iphdr' and is usually due to 'struct ef4_loopback_payload' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
struct iphdr ip;
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two bytes of padding to the start of struct efx_loopback_payload,
which are not sent on the wire. This ensures the 'ip' member is
4-byte aligned, preventing the following W=1 warning:
net/ethernet/sfc/siena/selftest.c:46:15: error: field ip within 'struct efx_loopback_payload' is less aligned than 'struct iphdr' and is usually due to 'struct efx_loopback_payload' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
struct iphdr ip;
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two bytes of padding to the start of struct efx_loopback_payload,
which are not sent on the wire. This ensures the 'ip' member is
4-byte aligned, preventing the following W=1 warning:
net/ethernet/sfc/selftest.c:46:15: error: field ip within 'struct efx_loopback_payload' is less aligned than 'struct iphdr' and is usually due to 'struct efx_loopback_payload' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
struct iphdr ip;
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
efx_net_stats() (.ndo_get_stats64) can be called during an ethtool
selftest, during which time nic_data->mc_stats is NULL as the NIC has
been fini'd. In this case do not attempt to fetch the latest stats
from the hardware, else we will crash on a NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000038
RIP efx_nic_update_stats
abridged calltrace:
efx_ef10_update_stats_pf
efx_net_stats
dev_get_stats
dev_seq_printf_stats
Skipping the read is safe, we will simply give out stale stats.
To ensure that the free in efx_ef10_fini_nic() does not race against
efx_ef10_update_stats_pf(), which could cause a TOCTTOU bug, take the
efx->stats_lock in fini_nic (it is already held across update_stats).
Fixes: d3142c193dca ("sfc: refactor EF10 stats handling")
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove ->sendpage() and ->sendpage_locked(). sendmsg() with
MSG_SPLICE_PAGES should be used instead. This allows multiple pages and
multipage folios to be passed through.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-afs@lists.infradead.org
cc: mptcp@lists.linux.dev
cc: rds-devel@oss.oracle.com
cc: tipc-discussion@lists.sourceforge.net
cc: virtualization@lists.linux-foundation.org
Link: https://lore.kernel.org/r/20230623225513.2732256-16-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-06-21
mlx5 driver minor cleanup and fixes to net-next
* tag 'mlx5-updates-2023-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Remove pointless vport lookup from mlx5_esw_check_port_type()
net/mlx5: Remove redundant check from mlx5_esw_query_vport_vhca_id()
net/mlx5: Remove redundant is_mdev_switchdev_mode() check from is_ib_rep_supported()
net/mlx5: Remove redundant MLX5_ESWITCH_MANAGER() check from is_ib_rep_supported()
net/mlx5e: E-Switch, Fix shared fdb error flow
net/mlx5e: Remove redundant comment
net/mlx5e: E-Switch, Pass other_vport flag if vport is not 0
net/mlx5e: E-Switch, Use xarray for devcom paired device index
net/mlx5e: E-Switch, Add peer fdb miss rules for vport manager or ecpf
net/mlx5e: Use vhca_id for device index in vport rx rules
net/mlx5: Lag, Remove duplicate code checking lag is supported
net/mlx5: Fix error code in mlx5_is_reset_now_capable()
net/mlx5: Fix reserved at offset in hca_cap register
net/mlx5: Fix SFs kernel documentation error
net/mlx5: Fix UAF in mlx5_eswitch_cleanup()
====================
Link: https://lore.kernel.org/r/20230623192907.39033-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/wpan/wpan-next
Miquel Raynal says:
====================
Core WPAN changes:
- Support for active scans
- Support for answering BEACON_REQ
- Specific MLME handling for limited devices
WPAN driver changes:
- ca8210:
- Flag the devices as limited
- Remove stray gpiod_unexport() call
* tag 'ieee802154-for-net-next-2023-06-23' of gitolite.kernel.org:pub/scm/linux/kernel/git/wpan/wpan-next:
ieee802154: ca8210: Remove stray gpiod_unexport() call
ieee802154: ca8210: Flag the driver as being limited
net: ieee802154: Handle limited devices with only datagram support
mac802154: Handle received BEACON_REQ
ieee802154: Add support for allowing to answer BEACON_REQ
mac802154: Handle active scanning
ieee802154: Add support for user active scan requests
====================
Link: https://lore.kernel.org/r/20230623195506.40b87b5f@xps-13
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
64-bit DMA detection will fail if axienet was started before (by boot
loader, boot ROM, etc). In this state axienet will not start properly.
XAXIDMA_TX_CDESC_OFFSET + 4 register (MM2S_CURDESC_MSB) is used to detect
64-bit DMA capability here. But datasheet says: When DMACR.RS is 1
(axienet is in enabled state), CURDESC_PTR becomes Read Only (RO) and
is used to fetch the first descriptor. So iowrite32()/ioread32() trick
to this register to detect 64-bit DMA will not work.
So move axienet reset before 64-bit DMA detection.
Fixes: f735c40ed93c ("net: axienet: Autodetect 64-bit DMA capability")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20230622192245.116864-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the devres variant of stmmac_pltfr_probe() and finally drop the
remove() callback entirely.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-12-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a devres variant of stmmac_pltfr_probe() which allows users to
skip calling stmmac_pltfr_remove() at driver detach.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-11-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Significantly simplify the driver's probe() function by using the devres
variant of stmmac_probe_config_dt(). This allows to drop the goto jumps
entirely.
The remove_new() callback now needs to be switched to
stmmac_pltfr_remove_no_dt().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-10-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a devres variant of stmmac_probe_config_dt() that allows users to
skip calling stmmac_remove_config_dt() at driver detach.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-9-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a variant of stmmac_pltfr_remove() that only frees resources
allocated by stmmac_pltfr_probe() and - unlike stmmac_pltfr_remove() -
does not call stmmac_remove_config_dt().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-8-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Shrink the code and remove labels by using the new stmmac_pltfr_probe()
function.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-7-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement stmmac_pltfr_probe() which is the logical API counterpart
for stmmac_pltfr_remove(). It calls the platform's init() callback and
then probes the stmmac device.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-6-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Shrink the code in dwmac-generic by using the new stmmac_pltfr_exit()
helper.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-5-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a helper wrapper around calling the platform's exit() callback.
This allows users to skip checking if the callback exists.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-4-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Shrink the code in dwmac-generic by using the new stmmac_pltfr_init()
helper.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-3-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a helper wrapper around calling the platform's init() callback.
This allows users to skip checking if the callback exists.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230623100417.93592-2-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-06-22 (ice)
This series contains updates to ice driver only.
Jake adds a slight wait on control queue send to reduce wait time for
responses that occur within normal times.
Maciej allows for hot-swapping XDP programs.
Przemek removes unnecessary checks when enabling SR-IOV and freeing
allocated memory.
Christophe Jaillet converts a managed memory allocation to a regular one.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: use ice_down_up() where applicable
ice: Remove managed memory usage in ice_get_fw_log_cfg()
ice: remove null checks before devm_kfree() calls
ice: clean up freeing SR-IOV VFs
ice: allow hot-swapping XDP programs
ice: reduce initial wait for control queue messages
====================
Link: https://lore.kernel.org/r/20230622183601.2406499-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzkaller reported use-after-free in __gtp_encap_destroy(). [0]
It shows the same process freed sk and touched it illegally.
Commit e198987e7dd7 ("gtp: fix suspicious RCU usage") added lock_sock()
and release_sock() in __gtp_encap_destroy() to protect sk->sk_user_data,
but release_sock() is called after sock_put() releases the last refcnt.
[0]:
BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
BUG: KASAN: slab-use-after-free in atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline]
BUG: KASAN: slab-use-after-free in queued_spin_lock include/asm-generic/qspinlock.h:111 [inline]
BUG: KASAN: slab-use-after-free in do_raw_spin_lock include/linux/spinlock.h:186 [inline]
BUG: KASAN: slab-use-after-free in __raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline]
BUG: KASAN: slab-use-after-free in _raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178
Write of size 4 at addr ffff88800dbef398 by task syz-executor.2/2401
CPU: 1 PID: 2401 Comm: syz-executor.2 Not tainted 6.4.0-rc5-01219-gfa0e21fa4443 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x72/0xa0 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:351 [inline]
print_report+0xcc/0x620 mm/kasan/report.c:462
kasan_report+0xb2/0xe0 mm/kasan/report.c:572
check_region_inline mm/kasan/generic.c:181 [inline]
kasan_check_range+0x39/0x1c0 mm/kasan/generic.c:187
instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline]
queued_spin_lock include/asm-generic/qspinlock.h:111 [inline]
do_raw_spin_lock include/linux/spinlock.h:186 [inline]
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline]
_raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178
spin_lock_bh include/linux/spinlock.h:355 [inline]
release_sock+0x1f/0x1a0 net/core/sock.c:3526
gtp_encap_disable_sock drivers/net/gtp.c:651 [inline]
gtp_encap_disable+0xb9/0x220 drivers/net/gtp.c:664
gtp_dev_uninit+0x19/0x50 drivers/net/gtp.c:728
unregister_netdevice_many_notify+0x97e/0x1520 net/core/dev.c:10841
rtnl_delete_link net/core/rtnetlink.c:3216 [inline]
rtnl_dellink+0x3c0/0xb30 net/core/rtnetlink.c:3268
rtnetlink_rcv_msg+0x450/0xb10 net/core/rtnetlink.c:6423
netlink_rcv_skb+0x15d/0x450 net/netlink/af_netlink.c:2548
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x700/0x930 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x91c/0xe30 net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0x1b7/0x200 net/socket.c:747
____sys_sendmsg+0x75a/0x990 net/socket.c:2493
___sys_sendmsg+0x11d/0x1c0 net/socket.c:2547
__sys_sendmsg+0xfe/0x1d0 net/socket.c:2576
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7f1168b1fe5d
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 9f 1b 00 f7 d8 64 89 01 48
RSP: 002b:00007f1167edccc8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004bbf80 RCX: 00007f1168b1fe5d
RDX: 0000000000000000 RSI: 00000000200002c0 RDI: 0000000000000003
RBP: 00000000004bbf80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007f1168b80530 R15: 0000000000000000
</TASK>
Allocated by task 1483:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
__kasan_slab_alloc+0x59/0x70 mm/kasan/common.c:328
kasan_slab_alloc include/linux/kasan.h:186 [inline]
slab_post_alloc_hook mm/slab.h:711 [inline]
slab_alloc_node mm/slub.c:3451 [inline]
slab_alloc mm/slub.c:3459 [inline]
__kmem_cache_alloc_lru mm/slub.c:3466 [inline]
kmem_cache_alloc+0x16d/0x340 mm/slub.c:3475
sk_prot_alloc+0x5f/0x280 net/core/sock.c:2073
sk_alloc+0x34/0x6c0 net/core/sock.c:2132
inet6_create net/ipv6/af_inet6.c:192 [inline]
inet6_create+0x2c7/0xf20 net/ipv6/af_inet6.c:119
__sock_create+0x2a1/0x530 net/socket.c:1535
sock_create net/socket.c:1586 [inline]
__sys_socket_create net/socket.c:1623 [inline]
__sys_socket_create net/socket.c:1608 [inline]
__sys_socket+0x137/0x250 net/socket.c:1651
__do_sys_socket net/socket.c:1664 [inline]
__se_sys_socket net/socket.c:1662 [inline]
__x64_sys_socket+0x72/0xb0 net/socket.c:1662
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 2401:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2e/0x50 mm/kasan/generic.c:521
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free mm/kasan/common.c:200 [inline]
__kasan_slab_free+0x10c/0x1b0 mm/kasan/common.c:244
kasan_slab_free include/linux/kasan.h:162 [inline]
slab_free_hook mm/slub.c:1781 [inline]
slab_free_freelist_hook mm/slub.c:1807 [inline]
slab_free mm/slub.c:3786 [inline]
kmem_cache_free+0xb4/0x490 mm/slub.c:3808
sk_prot_free net/core/sock.c:2113 [inline]
__sk_destruct+0x500/0x720 net/core/sock.c:2207
sk_destruct+0xc1/0xe0 net/core/sock.c:2222
__sk_free+0xed/0x3d0 net/core/sock.c:2233
sk_free+0x7c/0xa0 net/core/sock.c:2244
sock_put include/net/sock.h:1981 [inline]
__gtp_encap_destroy+0x165/0x1b0 drivers/net/gtp.c:634
gtp_encap_disable_sock drivers/net/gtp.c:651 [inline]
gtp_encap_disable+0xb9/0x220 drivers/net/gtp.c:664
gtp_dev_uninit+0x19/0x50 drivers/net/gtp.c:728
unregister_netdevice_many_notify+0x97e/0x1520 net/core/dev.c:10841
rtnl_delete_link net/core/rtnetlink.c:3216 [inline]
rtnl_dellink+0x3c0/0xb30 net/core/rtnetlink.c:3268
rtnetlink_rcv_msg+0x450/0xb10 net/core/rtnetlink.c:6423
netlink_rcv_skb+0x15d/0x450 net/netlink/af_netlink.c:2548
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x700/0x930 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x91c/0xe30 net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0x1b7/0x200 net/socket.c:747
____sys_sendmsg+0x75a/0x990 net/socket.c:2493
___sys_sendmsg+0x11d/0x1c0 net/socket.c:2547
__sys_sendmsg+0xfe/0x1d0 net/socket.c:2576
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
The buggy address belongs to the object at ffff88800dbef300
which belongs to the cache UDPv6 of size 1344
The buggy address is located 152 bytes inside of
freed 1344-byte region [ffff88800dbef300, ffff88800dbef840)
The buggy address belongs to the physical page:
page:00000000d31bfed5 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88800dbeed40 pfn:0xdbe8
head:00000000d31bfed5 order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
memcg:ffff888008ee0801
flags: 0x100000000010200(slab|head|node=0|zone=1)
page_type: 0xffffffff()
raw: 0100000000010200 ffff88800c7a3000 dead000000000122 0000000000000000
raw: ffff88800dbeed40 0000000080160015 00000001ffffffff ffff888008ee0801
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88800dbef280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88800dbef300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88800dbef380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88800dbef400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88800dbef480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: e198987e7dd7 ("gtp: fix suspicious RCU usage")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20230622213231.24651-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-06-22 (iavf)
This series contains updates to iavf driver only.
Przemek defers removing, previous, primary MAC address until after
getting result of adding its replacement. He also does some cleanup by
removing unused functions and making applicable functions static.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
iavf: make functions static where possible
iavf: remove some unused functions and pointless wrappers
iavf: fix err handling for MAC replace
====================
Link: https://lore.kernel.org/r/20230622165914.2203081-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linux provides phy_set_bits() helper so let's drop brcm_phy_setbits() and
use phy_set_bits() in its place.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230622184721.24368-1-giulio.benetti@benettiengineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
igc: TX timestamping fixes
This is the fixes part of the series intended to add support for using
the 4 timestamp registers present in i225/i226.
Moving the timestamp handling to be inline with the interrupt handling
has the advantage of improving the TX timestamping retrieval latency,
here are some numbers using ntpperf:
Before:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -56 +9 +52 19
1500 150 0.00% 0.00% 0.00% 100.00% -40 +30 +75 22
2250 225 0.00% 0.00% 0.00% 100.00% -11 +29 +72 15
3375 337 0.00% 0.00% 0.00% 100.00% -18 +40 +88 22
5062 506 0.00% 0.00% 0.00% 100.00% -19 +23 +77 15
7593 759 0.00% 0.00% 0.00% 100.00% +7 +47 +5168 43
11389 1138 0.00% 0.00% 0.00% 100.00% -11 +41 +5240 39
17083 1708 0.00% 0.00% 0.00% 100.00% +19 +60 +5288 50
25624 2562 0.00% 0.00% 0.00% 100.00% +1 +56 +5368 58
38436 3843 0.00% 0.00% 0.00% 100.00% -84 +12 +8847 66
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 0.00% 0.00% 100.00% 0.00%
291871 16384 27.35% 0.00% 72.65% 0.00%
437806 16384 50.05% 0.00% 49.95% 0.00%
After:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -44 +0 +61 19
1500 150 0.00% 0.00% 0.00% 100.00% -6 +39 +81 16
2250 225 0.00% 0.00% 0.00% 100.00% -22 +25 +69 15
3375 337 0.00% 0.00% 0.00% 100.00% -28 +15 +56 14
5062 506 0.00% 0.00% 0.00% 100.00% +7 +78 +143 27
7593 759 0.00% 0.00% 0.00% 100.00% -54 +24 +144 47
11389 1138 0.00% 0.00% 0.00% 100.00% -90 -33 +28 21
17083 1708 0.00% 0.00% 0.00% 100.00% -50 -2 +35 14
25624 2562 0.00% 0.00% 0.00% 100.00% -62 +7 +66 23
38436 3843 0.00% 0.00% 0.00% 100.00% -33 +30 +5395 36
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 19.50% 0.00% 80.50% 0.00%
291871 16384 35.81% 0.00% 64.19% 0.00%
437806 16384 55.40% 0.00% 44.60% 0.00%
During this series, and to show that as is always the case, things are
never easy as they should be, a hardware issue was found, and it took
some time to find the workaround(s). The bug and workaround are better
explained in patch 4/4.
Note: the workaround has a simpler alternative, but it would involve
adding support for the other timestamp registers, and only using the
TXSTMP{H/L}_0 as a way to clear the interrupt. But I feel bad about
throwing this kind of resources away. Didn't test this extensively but
it should work.
Also, as Marc Kleine-Budde suggested, after some consensus is reached
on this series, most parts of it will be proposed for igb.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Work around HW bug causing missing timestamps
igc: Retrieve TX timestamp during interrupt handling
igc: Check if hardware TX timestamping is enabled earlier
igc: Fix race condition in PTP tx code
====================
Link: https://lore.kernel.org/r/20230622165244.2202786-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the list of next hops from struct mlxsw_sp_rif to mlxsw_sp_crif. The
reason is that eventually, next hops for mlxsw uppers should be offloaded
and unoffloaded on demand as a netdevice becomes an upper, or stops being
one. Currently, next hops are tracked at RIFs, but RIFs do not exist when a
netdevice is not an mlxsw uppers. CRIFs are kept track of throughout the
netdevice lifetime.
Correspondingly, track at each next hop not its RIF, but its CRIF (from
which a RIF can always be deduced).
Note that now that next hops are tracked at a CRIF, it is not necessary to
move each over to a new RIF when it is necessary to edit a RIF. Therefore
drop mlxsw_sp_nexthop_rif_migrate() and have mlxsw_sp_rif_migrate_destroy()
call mlxsw_sp_nexthop_rif_update() directly.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/e7c1c0a7dd13883b0f09aeda12c4fcf4d63a70e3.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nexthop finalization consists of two steps: the part where the offload is
removed, because the backing RIF is now gone; and the part where the
association to the RIF is severed.
Extract from mlxsw_sp_nexthop_type_fini() a helper that covers the
unoffloading part, mlxsw_sp_nexthop_type_rif_gone(), so that it can later
be called independently.
Note that this swaps around the ordering of mlxsw_sp_nexthop_ipip_fini()
vs. mlxsw_sp_nexthop_rif_fini(). The current ordering is more of a
historical happenstance than a conscious decision. The two cleanups do not
depend on each other, and this change should have no observable effects.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/7134559534c5f5c4807c3a1569fae56f8887e763.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A previous patch added a pointer to loopback CRIF to the router data
structure. That makes the loopback RIF index redundant, as everything
necessary can be derived from the CRIF. Drop the field and adjust the code
accordingly.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/8637bf959bc5b6c9d5184b9bd8a0cd53c5132835.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a RIF is about to be created, the registration of the netdevice that
it should be associated with must have been seen in the past, and a CRIF
created. Therefore make this a hard requirement by looking up the CRIF
during RIF creation, and complaining loudly when there isn't one.
This then allows to keep a link between a RIF and its corresponding
CRIF (and back, as the relationship is one-to-at-most-one), which do.
The CRIF will later be useful as the objects tracked there will be
offloaded lazily as a result of RIF creation.
CRIFs are created when an "interesting" netdevice is registered, and
destroyed after such device is unregistered. CRIFs are supposed to already
exist when a RIF creation request arises, and exist at least as long as
that RIF exists. This makes for a simple invariant: it is always safe to
dereference CRIF pointer from "its" RIF.
To guarantee this, CRIFs cannot be removed immediately when the UNREGISTER
event is delivered. The reason is that if a RIF's netdevices has an IPv6
address, removal of this address is notified in an atomic block. To remove
the RIF, the IPv6 removal handler schedules a work item. It must be safe
for this work item to access the associated CRIF as well.
Thus when a netdevice that backs the CRIF is removed, if it still has a
RIF, do not actually free the CRIF, only toggle its can_destroy flag, which
this patch adds. Later on, mlxsw_sp_rif_destroy() collects the CRIF.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/68c8e33afa6b8c03c431b435e1685ffdff752e63.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CRIFs are generally not maintained for loopback RIFs. However, the RIF for
the default VRF is used for offloading of blackhole nexthops. Nexthops
expect to have a valid CRIF. Therefore in this patch, add code to maintain
CRIF for the loopback RIF as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/7f2b2fcc98770167ed1254a904c3f7f585ba43f0.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Linus Torvalds
Arnd Bergmann
Jason Gunthorpe
Moritz Fischer
Jakub Kicinski
Vladimir Oltean
Julia Lawall
Davide Tronchin
Cambda Zhu
Daniel Lezcano
Edward Cree
David Howells
Maxim Kochetkov
Bartosz Golaszewski
Kuniyuki Iwashima
Giulio Benetti
Petr Machata
