diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/arm/boot/dts/meson8b-odroidc1.dts | 24 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 26 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts | 36 | ||||
| -rw-r--r-- | arch/arm64/configs/defconfig | 3 |
4 files changed, 48 insertions, 41 deletions
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts index 73cdfe855689..941682844faf 100644 --- a/arch/arm/boot/dts/meson8b-odroidc1.dts +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts @@ -281,19 +281,6 @@ "J7 Header Pin 6", "J7 Header Pin 5", "J7 Header Pin 7", "HDMI_CEC", "SYS_LED", "", ""; - - /* - * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal - * to be turned high in order to be detected by the USB Controller. - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub { - gpio-hog; - gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; }; &ir_receiver { @@ -381,5 +368,16 @@ }; &usb1 { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; status = "okay"; + + hub@1 { + /* Genesys Logic GL852G usb hub */ + compatible = "usb5e3,610"; + reg = <1>; + vdd-supply = <&p5v0>; + reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>; + }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index 201596247fd9..01356437a077 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -250,21 +250,6 @@ }; }; -&gpio_ao { - /* - * WARNING: The USB Hub on the Odroid-C2 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - hog-0 { - gpio-hog; - gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; -}; - &hdmi_tx { status = "okay"; pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; @@ -414,5 +399,16 @@ }; &usb1 { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; status = "okay"; + + hub@1 { + /* Genesys Logic GL852G USB 2.0 hub */ + compatible = "usb5e3,610"; + reg = <1>; + vdd-supply = <&p5v0>; + reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>; + }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts index 8c30ce63686e..d04768a66bfe 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts @@ -26,20 +26,30 @@ sound { model = "ODROID-C4"; }; -}; -&gpio { - /* - * WARNING: The USB Hub on the Odroid-C4 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - hog-0 { - gpio-hog; - gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; + /* USB hub supports both USB 2.0 and USB 3.0 root hub */ + usb-hub { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.0 hub on port 1 */ + hub_2_0: hub@1 { + compatible = "usb2109,2817"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + + /* 3.1 hub on port 4 */ + hub_3_0: hub@2 { + compatible = "usb2109,817"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; }; }; diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 989183c76ae0..7e0487bbdaa0 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -938,6 +938,7 @@ CONFIG_USB_SERIAL_FTDI_SIO=m CONFIG_USB_SERIAL_OPTION=m CONFIG_USB_QCOM_EUD=m CONFIG_USB_HSIC_USB3503=y +CONFIG_USB_ONBOARD_HUB=m CONFIG_NOP_USB_XCEIV=y CONFIG_USB_GADGET=y CONFIG_USB_RENESAS_USBHS_UDC=m @@ -960,6 +961,8 @@ CONFIG_TYPEC_TCPCI=m CONFIG_TYPEC_FUSB302=m CONFIG_TYPEC_TPS6598X=m CONFIG_TYPEC_HD3SS3220=m +CONFIG_TYPEC_UCSI=m +CONFIG_UCSI_CCG=m CONFIG_TYPEC_MUX_GPIO_SBU=m CONFIG_MMC=y CONFIG_MMC_BLOCK_MINORS=32 |